Replacement Hardware for Curt Trailer Hitch 31374

Question

Question:

I need hardware kit 31374-BK for curt hitch 31374. Do you have this available?

asked by: Mark M

0

Expert Reply:

We have replacement install hardware for all of the hitches we carry including the Curt # 31374 you mentioned with the part # RHK. The number you mentioned is a Curt part number but our RHK comes with the same hardware.

expert reply by: Jameson C

0

Answer 1

When replacing the hardware for your Curt Front Mount Hitch #31374 you will need The Replacement Hardware Kit #RHK. When on the product page there will be two boxes that you will have to fill out. The first one you will type in 31374. The second box…

view full answer...

Answer 2

We have just what you need. If you type RHK in the search box on our website it will take you to the replacement hardware kit product page. You will then simply type the number of the hitch you need hardware for in the box that is labeled Hitch Item…

view full answer...

Answer 3

Hey Kevin, The hardware for your Curt Front Mount Trailer Hitch Receiver #31374 can be purchased by entering in 31374 into the 'Hitch Item Number' box above the add to cart button on the #RHK product page. You can also reach out to Curt…

view full answer...

Answer 4

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 5

Hi Stan! The SnowBear Snowplow for 2" Hitches - 82" Wide x 19" Tall #K2AVAL8219 and Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2" #C31018 will definitely work on your 2013 Ford F-250 4x4. We actually have both of these…

view full answer...

Answer 6

Hey Dean, the Detail K2 Elite Snowplow part #K2AVAL8219ELT that you referenced comes with all of the electrical components it will need to install. It wires to the vehicle battery as well as comes with a wired switch that you would run to the cab of…

view full answer...

Answer 7

There are no skid plate fit notes for the front mount hitches for your 2014 Ram 1500. That would lead me to believe that the skid plate of your truck is aftermarket. Which the best recommendation I can make would be for you to check out the install…

view full answer...

Answer 8

We have not had a chance to test fit the front-mount hitch that fits your 2017 Ram 1500 4WD - the Curt #31374 - on a '17 model so there is not an exact distance from the ground to the bottom of the hitch available. However, the installation will…

view full answer...

Answer 9

Hey Steven, The trim can vary between different sub models so I can't give you an exact measurement without actually measuring your specific model. If you measure down from the front tow hook bolt hole in the mounting brackets of the EcoHitch…

view full answer...

Answer 10

I spoke with my contact at Detail K2 who said that the height of the front hitch receiver on your 2005 Jeep Wrangler needs to be within the range of 13" - 18" which is measured to the bottom of the receiver opening. This is the case for all…

view full answer...

Answer 11

The 2 inch receiver for the EcoHitch Hidden Front Mount Trailer Hitch #306-X7900 referenced in your question will actually protrude through the grille of your truck. This allows for a really clean appearance while also maintaining your existing…

view full answer...

Answer 12

A 9,000 pound trailer should have a tongue weight of 900 to 1,350 pounds, maybe a little more, so any jack that has a capacity higher than the tongue weight would work. But the higher the capacity of the jack the easier it will be for it to lift the…

view full answer...

Replacement Hardware for Curt Trailer Hitch 31374

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching