Replacement Air Line Kit for Air Lift Ride Control

Question

Question:

I have airlift in rear part number 59530 what replacement kit will work

asked by: Todd G

0

Expert Reply:

The correct replacement air line kit for an Air Lift Ride Control kit part # AL59530 that you have is the part # AL20086.

expert reply by: Jameson C

0

Answer 1

Most likely not as the bags are typically different sizes between vehicle fits so the best solution would be an all new Air Lift Load Lifter like the part #AL57289 which fits your 2022 Ram 2500. If you let me know what your old truck was though I can…

view full answer...

Answer 2

For your 2019 Ram 2500, I recommend the 5,000 lbs Air Lift LoadLifter Air Helper Springs item #AL57289 over the higher capacity 7,500 lbs item #AL57589. 5,000 lbs capacity is more than enough for your truck. The higher capacity ones would affect the…

view full answer...

Answer 3

The wiring harness you see pictured with replacement gauge #AL25194 is attached to the gauge assembly itself so it is included. You would just need to wire it in to the rest of the system and attach the air line to the back. If you also need the air…

view full answer...

Answer 4

The air line that comes with the #AL88105 SHOULD be long enough for your application as it is 16 feet long and the replacement is #AL20086. The air line wouldn't need to run to the engine bay as it normally runs to cab. But we do have a 30 foot…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Hey Todd, welcome back! An air compressor like the Air Lift WirelessONE Compressor System for Air Helper Springs #AL25980EZ comes with everything you need for installation. This is compatible with the braided lines on your existing air bags, so you…

view full answer...

Replacement Air Line Kit for Air Lift Ride Control

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching