Availability of B and W Gooseneck Hitch Cover that Can Fit Square Hitch Hole

Question

Question:

Hello, I bought a truck that had a gooseneck ball in the bed. When I pull this ball out I know have a hole that Im wanting to cover. The ball that came out is square. I have looked everywhere for a cover to put in this hole. Do you guys sell this part? Thanks,

asked by: Tim A

0

Expert Reply:

The B&W Rubber Cover for Empty Turnoverball Socket # BWGNXA1715 is designed to fit a square gooseneck hitch hole. This cover is designed to fit a 2-1/2 inch square hole so you might measure what you have now to see if this would fit or not.

expert reply by: Jameson C

0

Answer 1

What gooseneck hitch do you have installed in the bed of your truck? That will dictate what the correct plug would be.

view full answer...

Answer 2

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 8

Hey Jordan! Based on your measurement you have a Lippert 1116 or 1716. If you want to confirm that feel free to send me the S/N on your pin box. The Gen-Y Nomad you were looking at is for the Rhino Box so that is not a fit. What you need is the Gen-Y…

view full answer...

Answer 9

Hey Jerry, GM moved the placement of their puck systems starting with 2020 models so you are correct that the pucks would have the hitch not sit directly over the axle. GM did the math and made sure that this placement wouldn't adversely affect…

view full answer...

Answer 10

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 11

Louie, Yes, that is a great question. You do not have to worry about the air bags interfering with your B&W Turnoverball hitch setup. The Firestone Ride-Rite Air Bags with Easy Mount Compressor and In-Cab Control #F84XV are compatible with in-bed…

view full answer...

Answer 12

Hey Jeff, Depending on how much clearance you need from that tailgate is going to determine what kind of hitch extender you will need. Assuming you just have a factory 2" hitch receiver on your Ram you could go with the hitch extender #e48YR…

view full answer...

Availability of B and W Gooseneck Hitch Cover that Can Fit Square Hitch Hole

Product Page this Question was Asked From

Continue Researching