Required Mounting Hardware For Titan Zinc-Plated Brake Actuator w/ Electric Lockout # T47457207K

Question

Question:

Do you know the length and the diameter of the bolts to use to mount it on your trailer

asked by: Frank B

0

Expert Reply:

The Titan Zinc-Plated Brake Actuator w/ Electric Lockout # T47457207K requires 2 grade 5 bolts that are 1/2" x 4" to bolt to the trailer tongue.

expert reply by: Bud M

0

Answer 1

A 7,000 lb capacity actuator like the part #T47457207K would work great with your boat and trailer that weighs a total of 2,200 lbs. This is a multi-fit coupler that will work with virtually any hitch ball size.

view full answer...

Answer 2

The Optronics 25 foot 4 Way Wire Harness #A25W2GWB will be a good option. This will generally have enough length to cover most trailers. I will also recommend adding in a few of the Spectro Self-Stripping Connector with Waterproof Sealant…

view full answer...

Answer 3

Hey Paul, Stop/turn signal light functions typically use the same wire and the running lights are on their own. You'll want to go to the passenger side and check the running light wire for power with a multimeter #PT89ZR. If you aren't…

view full answer...

Answer 4

Hello Lonnie, thanks for reaching out. The 30 ft. Wishbone 4-Way Trailer Wiring Harness with 30" Ground Wire #A30WB is 20 gauge wire. I walked out to our warehouse and looked at one to confirm this.

view full answer...

Answer 5

To bolt the Titan Model 20 to your trailer tongue you want to use 2- 5/8" by 4" grade 5 bolts, nuts and lock washers. If the tongue is a light weight tongue (narrower than 3" wide) you want to use spacer tubes inside for reinforcement…

view full answer...

Answer 6

The Titan brake actuator #T43397007K will take 1/2 inch by 4 inch grade 5 bolts, nuts, and lock washers. Since this is a boat trailer if you can find some grade 5 zinc coated or stainless steel they will have better corrosion resistance. I have…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Required Mounting Hardware For Titan Zinc-Plated Brake Actuator w/ Electric Lockout # T47457207K

Product Page this Question was Asked From

Continue Researching