What Size is the Valve Stem Hole on the Aluminum Jaguar Trailer Wheel

Question

Question:

What is the diameter of the hole for the valve stem?

asked by: Ken M

1

Helpful Expert Reply:

The diameter for the valve stem hole on the Aluminum Jaguar Trailer Wheel # 274-000011 is 0.625".

expert reply by: Scott S

1

Answer 1

Hey Vince, yes the trailer wheel part #274-000011 would be able to easily handle the 110 psi you mentioned. It more or less comes down to the valve stem more than anything so as long you have something like the part #274-000011 that can handle the…

view full answer...

Answer 2

The Aluminum Jaguar Wheel #274-000011 does not have a PSI rating, but it's included valve stem does and is rated to 80 PSI. If the tire you're installing requires more air pressure then that, you'll just need to replace the included valve…

view full answer...

Answer 3

Since wheels will be able to withstand the psi rating of any of the tires that are meant to fit it you will need to look at the valve stem as that is the deciding factor. If your valve stem has the rubber all the way up to the threads, like part…

view full answer...

Answer 4

The wheel on a trailer will typically always be higher than any tire that can be mounted. The limiting factory is the valve stem. A solid metal one, like the Americana Metal, Bolt-In Valve Stem #AM20906, will be rated to to 200 psi, whereas a valve…

view full answer...

Answer 5

Here is a list of our 16" steel trailer wheels which have the 6 on 5-1/2" bolt pattern. We will not have any wheels which have the 95.4mm pilot hole you are needing which should not likely be an issue since trailers will typically use a…

view full answer...

Answer 6

A ST235/80-16 tire will fit on a 16 inch rim with a width of 6, 6-1/2, 7 or 7-1/2 inches. Threfore the #AM20742 rim you'd looked at would work well for you. The rim has a 6 on 5-1/2 inch bolt pattern and a 3050 lb capacity. You'll also need…

view full answer...

Answer 7

Hey Steve, thanks for reaching out! The 1/2"-20 Taskmaster Trailer Wheel Lug Nut #TA66QR has a 1-3/8" overall length and it can be installed with a 3/4" socket. The only real difference between the Taskmaster #TA66QR and DeeMaxx…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

What Size is the Valve Stem Hole on the Aluminum Jaguar Trailer Wheel

Continue Researching