Replacement Parts For CE Smith Bunk-Style Guide-Ons Set # CE27660 To Build a Single Side

Question

Question:

I want to purchase a bunk guide on product. the item number I found is for a pair item # CE27660 can i purchase just one?

asked by: Gerald W

0

Expert Reply:

We do offer the following replacement parts that will allow you to just get a single bunk guide like those found in the CE Smith Bunk-Style Guide-Ons Set # CE27660.

Replacement Upright # CE27609PG Qty 1
CE Smith Swivel Bracket # CE10200G Qty 2
Replacement CE Smith Guide-On Mounting U-Bracket # CES94FR Qty 1
CE Smith U-Bolt Kit # CES44FR Qty 1
CE Smith Deluxe Marine-Grade Carpeting # CE11372

You will need to source the lumber for the bunk board and hardware for the swivel bracket locally as we do not carry those separately.

expert reply by: Bud M

0

Answer 1

It sounds like you may be needing a kit like the CE Smith Bunk-Style Guide-On Kit #CE27600K90. We do have just the Upright #CE27608PG and Mounting Bracket #CES94FR individually if that is all you are needing. The U-Bolt Kit #CES44FR will allow you to…

view full answer...

Answer 2

Yes, the replacement upright for CE Smith Guide-Ons #CE27660 is available by itself. It is part #CE27609PG.

view full answer...

Answer 3

Two 12 foot long bunks boards will work well to support your 21 foot boat. Ideally, the bunk boards should be at least half as long as your boat and run from the stern (or a few inches beyond it) to the bow as far forward as you like. Due to shipping…

view full answer...

Answer 4

Hi John; there is no specific position you need to drill the holes for the swivel brackets on the #CE27600K90. Choose a position that works best for your setup which is likely toward the top. The swivel brackets use a 1/2" bolt, I would hold up…

view full answer...

Answer 5

Hey Michael, Thanks for the info, and the part number you referenced is actually one from a different retailer, but using that I was able to track down that you were referencing the CE Smith Bunk-Style Guide-Ons #CE27600. And you do indeed have the…

view full answer...

Answer 6

I was able to track down some measurements for the 90 degree uprights that are included with the #CE27600K90 bunk kit. Hope this helps. See below: A: Internal Distance - 15-1/2" A: External Distance - 17" B: Internal Distance - 18" B:…

view full answer...

Answer 7

The Slotted Swivel Bracket for Boat Trailers #HP55FR is 11 gauge which is approximately 1/8 of an inch.

view full answer...

Answer 8

They would indeed work together. The #HP55FR is the portion that would attach directly to the bunk which would attach to the #CE10101G bolster bracket would would attach to the trailer itself. When the bolster and swivel are assembled, they'd…

view full answer...

Answer 9

Hey Ray, so we have the part #CE15253A which is 4 inches long and has a 3-1/8 inch width with a 7/16 inch diameter. If you were looking for more of a guide on style U-bolt kit that criss crosses we have the part #CES44FR as our closest option as…

view full answer...

Answer 10

For your 2021 G3 Bay 18 DLX, the closest option we can offer is the CE Smith Bunkboard Guide-On Kit #CE27600K75, which has 75° posts and will create a more "tucked-in" look, as oppose to the 90° kit #CE27600K90.

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Replacement Parts For CE Smith Bunk-Style Guide-Ons Set # CE27660 To Build a Single Side

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching