Diameter of the Inner Ring of the Dexstar Conventional Steel Wheel # AM20758 for Baby Moon Hubcaps

Question

Question:

Can you measure the outside diameter / dimension of the ring where Baby Moon Hubcaps would snap onto where the nibs are located. Im trying to determine if Im going to be able to find Baby Moons for this 16inch Steel Rim. Thanks

asked by: Mark

0

Expert Reply:

We have the Dexstar Conventional Steel Wheel, # AM20758, in stock so I went out to the warehouse to get an exact measurement for you. The outside diameter of the inner ring of this wheel is 11-1/2 inches including the nibs.

expert reply by: John H

0

click to enlarge

Answer 1

You can determine whether either of our baby moon hubcaps, part #AM90086 or part #AM981306, will fit a wheel by measuring the outer diameter of the inner ring and then the outer diameter of the inner ring with one of the tabs (see attached photo).…

view full answer...

Answer 2

Appreciate the purchase, and there is a hubcap option that fits the Dexstar Conventional Steel Wheel - 16" x 6" Rim - 6 on 5-1/2 - Black Powder Coat #AM20758: - Phoenix USA Baby Moon Hubcap - Stainless Steel #PX1309SS

view full answer...

Answer 3

I spoke with my contact at Redline and he said that the Replacement Screw-In Wheel Stud, #25-53, is an industry standard grade 5. This replacement wheel stud will be equivalent to, or surpass, the load capacity of the old lug bolts that you are…

view full answer...

Answer 4

We do have replacement studs, but since we do not carry AL-KO products I am unsure as to a specific fit. I have attached a link that has our available list of replacement studs for you to look through. You will simply need to make sure that you check…

view full answer...

Answer 5

I went out into our warehouse to get the dimensions of the Dexstar Conventional Wheel part #Am20758 that you requested. From the opposite end of a nub to the other side of the round portion of the rim that sticks out this wheel measures 11-9/16…

view full answer...

Answer 6

Hey Joe, yes the PowerMax RV Toilet #PM42VR that you referenced does come with a seal for the floor and everything else needed to install. I attached a picture that shows all of the hardware that comes with this as well.

view full answer...

Answer 7

Yes, it is James. The PowerMax 310 RV Toilet item #PM42VR is a Dometic 310 toilet. The PowerMax label is a high-performance flushing system featuring a powerful swirl-jet cleaning action. The PowerMax 310 RV Toilet item #PM42VR has a elongated seat…

view full answer...

Answer 8

I wasn't able to get exact info on your part number, but from the part number we know it's right hand thread wheel bolt like the part #RG02-020 which is a fine thread 1/2 inch diameter bolt with a 60 degree angled head. The other most likely…

view full answer...

Answer 9

The degrees represents the angle of the cone that is on the wheel bolt. If they are 90 degree then the cone is a 90 degree angle made by the angle created by each side of the bolt. A 60 degree lug bolt would have a 60 degree angle made by each sides…

view full answer...

Answer 10

The part you referenced, Redline #25-53 Replacement Screw-In Wheel Stud, has a fine thread pitch and a 1/2-inch diameter. If this matches your trailer's wheel stud then you can use a lubricant to remove the old stud and replace it with this one…

view full answer...

Answer 11

Yes, you will want to use the Loctite Threadlocker 242 - Medium Strength - 1/4" to 3/4" Nuts/Bolts item #LT37418 to install the Redline Replacement wheel studs item #25-53. This is the blue one you will be able to remove your studs in the…

view full answer...

Answer 12

The wheel bolt hole diameters of the #AM20758 is just slightly over 1/2 inch which allows only 1/2 inch wheel studs to fit through. You wouldn't be able to fit a 9/16 inch or larger stud through the hole. The lug nuts to be used with this wheel…

view full answer...

Diameter of the Inner Ring of the Dexstar Conventional Steel Wheel # AM20758 for Baby Moon Hubcaps

Product Page this Question was Asked From

Continue Researching