Recommended Stainless Steel Door Holders With A 1 x 2-1/4 Mounting Pattern
Updated 08/30/2022 | Published 08/29/2022
Products Featured in This Question
Question:
My trailer has plastic door holds that bent in a strong wind. Im looking to replace them with stainless steel. My side door is about 5 inches center of pivot to center of the tab. The rear doors are 9 inches. The mounting holes are the same at 1 x 2 1/4. Shorter holds would be fine but will they line up using the existing holes in the trailer and door? I would go to 4 on the side and 6 inch for the rear doors. Thank you.
asked by: Gerry
Expert Reply:
The T-Style Hook and Keeper Door Holder for RV or Enclosed Trailer - 6" Hook # 37210525 and 4" # 37210515 both have a mounting pattern of 1" x 2-1/4" (seen below) so you should be good to just reuse your current mounting holes. I do recommend putting some butyl tape # AL28FJ on the bracket to help seal up those mounting holes so that water doesn't leak through.
(click to enlarge)
Product Page this Question was Asked From
T-Style Hook and Keeper Door Holder for RV or Enclosed Trailer - 6" Hook - Stainless Steel
- Trailer Door Holders
- Hook and Keeper
- Straight
- 6 Inch Long
- 1 x 2-1/4 Inch Hole Spacing
- Stainless Steel
- JR Products
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Search Results: paper towel holder
- Search Results: waterproof hatch
- Search Results: rv exterior lights
- Search Results: boat hatch
- Search Results: paper towel holder trailer cargo organizers
- Search Results: rv interior lights
- Video: Review of RV Designer RV Door Parts - Entry Door - RD67ZR
- Shop: RV Designer T-Style Entry Door Holder w/ Bumper - 3-3/4" - Stainless Steel
- Search Results: trailer door holders
- Shop: RV Exterior Lighting
- Shop: T-Style Hook and Keeper Door Holder for RV or Enclosed Trailer - 4" Hook - Stainless Steel
- Video: All About the T-Style Hook and Keeper Door Holder for RV or Enclosed Trailer
- Shop: Alpha Systems Butyl Tape for RV Weatherproofing - 20' x 1" x 3/16"
- Shop: RV Designer 90-Degree Entry Door Holder - Plastic - Black
- Shop: RV Designer 90-Degree Entry Door Holder - Plastic - White
- Shop: RV Designer T-Style Self-Closing Entry Door Holder - 4" - Stainless Steel
- Shop: Adco SFS AquaShed Trailer Cover for Bumper Pull Horse Trailers up to 12' Long - Gray
- Article: Diode Installation Instructions for a Dinghy with Separate Tail Light Wiring
- Article: How to Measure for Motorhome Steps
- Video: Breaking Down the Valterra Folding Manual Stabilizer for Trailers and RVs
- Q&A: Best Cover for a 28 Foot Enclosed Trailer
- Video: Feature Review 90-Degree T-Style Hook and Keeper Door Holder for Enclosed Trailer
- Q&A: Ways To Keep Entry Door On Keystone Outback Travel Trailer From Slamming Open & Closed due to Wind
- Shop: Battery
- Q&A: Weight Capacity of Valterra Folding Manual Stabilizer for Trailers and RVs 020106
- Q&A: Adding a Battery on an Enclosed Trailer to Power Interior Lights
- Q&A: Powering Interior Trailer Lights With Generator
- Video: Checking Out the T-Style Hook and Keeper Door Holder for RV or Enclosed Trailer
- Shop: Trailer Wiring
- Video: Americana Trailer Wheel Center Cap Review
on RV Door Parts
