Parts Needed For Mounting Buyers Products 25 Ton Swivel Type Pintle Hook # 337BP200

Question

Question:

what size bolts are used for this hitch Thank U

asked by: Gordon B

1

Helpful Expert Reply:

For mounting the Buyers Products 25 Ton Swivel Type Pintle Hook # 337BP200 it is recommended to use (6) 1/2 in. x 2-1/2 in Grade 8 cap screws, (6) 1/2 in. Grade 8 hex nuts, and (6) 1/2 in. heavy lock washers.

expert reply by: Bud M

1

Mike R.

6/27/2025

Do you sell these bolts

Robin H.

6/28/2025

@MikeR the bolts are something you will need to pick up at your local hardware store.

Answer 1

The mounting surface can not be thicker than half an inch (1/2 inch or .5 inches). I went to the warehouse to measure the Buyers Products 25 Ton Swivel Type Pintle Hook #337BP200 myself. The distance between the mounting surfaces had half an inch of…

view full answer...

Answer 2

I've edited a photo for you that shows the bolt hole pattern of the Buyers Products #337BP200 Swivel Pintle Hook. If you click the provided link, you can see a product description video featuring the pintle hook.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 5

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 6

Hi Ken! It looks like you have almost everything you need to set up your 2026 Jeep Gladiator Sahara for flat towing. The etrailer Invisible Base Plate Kit - Removable Arms #e98948 is a perfect fit and the etrailer XHD Non-Binding Tow Bar - RV Mount -…

view full answer...

Answer 7

Hello Albert, thanks for reaching out. I looked up those part numbers and they come back as 12"x2" brake assemblies for a 6K-7K axle. We do have suitable replacements for these. Here is what I recommend: - etrailer Electric Trailer Brakes -…

view full answer...

Answer 8

The Kodiak Disc Brake Kit #K2HR10A11RERR is actually specifically designed to fit an AL-KO 10k #99 spindle, so this will be a perfect replacement. Though this does include the oil cap, it should be noted that it does not include the bearings or seal.…

view full answer...

Answer 9

The closest metric trailer tire size to a 4.80x12 is going to be a 145/80-12. The typical diameter of a 4.80x12 tire is 20.5 inches. On a 145/80-12, it is 21.3 inches. So the metric size will be a little over 1/4 inch taller. Make sure to measure the…

view full answer...

Answer 10

To replace the latch (or jaw) on the Buyers Products 30 Ton Pintle Hook #337PH30, and to save Carl, you just need this part: - Replacement Jaw for Buyers Products 30 Ton Pintle Hook #3373002981

view full answer...

Answer 11

Hey Wendell, thanks for the information! Since you have a Lippert 122093 hub for a 5,200 lbs axle you'll need the Bearing Kit item #BK3-300. This kit includes inner and outer bearings, races, a grease seal, and a replacement cotter pin. This kit…

view full answer...

Answer 12

It looks like your axles are 3,500 lb axles, but I couldn't find any info regarding the size of the size of the spindle where the seal rides, or the hub bore. So long as the spindle measures 1.72" where the seal rides, and the hub bore…

view full answer...

Parts Needed For Mounting Buyers Products 25 Ton Swivel Type Pintle Hook # 337BP200

Product Page this Question was Asked From

Continue Researching