What Bolt is Needed for the Replacement Track Nut for Thule Tracker Roof Rack Fit Kit TK4

Question

Question:

Replacement Track Nut for Thule Tracker Roof Rack Fit Kit TK4 What size bolt do I need ?

asked by: Jon

0

Expert Reply:

The correct bolt for the Replacement Track Nut for Thule Tracker Roof Rack Fit Kit TK4 # 853-5147 is the Replacement M6 x 17 mm Bolt # 924-0617-15 which is a M6 x 17 mm.

expert reply by: Scott S

0

Answer 1

Hello Jerome. In order to install your Thule Evo Aero Bars into the T-slots, you will need the Fit Kit for Thule Podium-Style Roof Rack Feet - 3101 #THKIT3101, and then the Rapid Podium Feet for Thule Crossbars - Fixed Point - Qty 4 #TH460R. Also,…

view full answer...

Answer 2

You're in a tough spot as Thule has basically phased out your entire roof rack setup from the feet, to the bars, and the fit kit. I wish I had something I could offer that was simple and easy but based on your situation I would go with option 4…

view full answer...

Answer 3

The Thule Roof Mounted Top Rack System - 60" Long, part #THTB60 works with the Rapid Podium Feet for Thule Crossbars - Fixed Point - Qty 4, part #TH460R, and the Fit Kit for Thule Podium-Style Roof Rack Feet - 3101, part #THKIT3101. The missing…

view full answer...

Answer 4

Tracks can absolutely be installed on the roof of your A.R.E. Truck Cap to provide a mounting system for a roof rack. For this I recommend the Yakima Tracks, which come in 42 inch #Y01126, 54 inch #Y01127, and 60 inch #Y01135 lengths. These tracks…

view full answer...

Answer 5

The difference between Landing Pad 1 #Y00221 and Landing Pad 4 #Y00224 is the hardware. For LP1 the 'A' plate dimension is 7/8" x 11/16" and for LP4 the 'C' plate dimension is 1 3/16" x 13/16" so they fit different…

view full answer...

Answer 6

You are correct, it is the Yakima Landing Pad 1 part #Y00221 that is compatible with the Truxedo Elevate TS rails.

view full answer...

Answer 7

I took a look at what we have, and all of the anchor plates like the Replacement Anchor Plate "A" for Yakima LandingPad 1 #Y8810074 are designed to be used with a 6mm or M6 bolt. What you could do is use the anchor plate #Y8810074, and just…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

What Bolt is Needed for the Replacement Track Nut for Thule Tracker Roof Rack Fit Kit TK4

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching