Will Hopkins HM09175 Hitch Level Fit Thumb Latch Coupler

Question

Question:

I have about 2 3/4” from the back of the hitch lever to the front jack mounting bolt. Will this bolt interfere with mounting the level?

asked by: Ron

0

Expert Reply:

Thanks for sending in a picture of your thumb latch coupler and trailer jack. Based on seeing that we know the Hopkins Trailer Hitch Level with Cover part # HM09715 would fit and work great as we had chance to install this on the exact same coupler as you can see in the attached review video.

expert reply by: Jameson C

0

Thumb Latch Coupler
(click to enlarge)

Answer 1

You will want to use a cobalt or titanium drill bit when drilling the 5/32-in pilot hole for the #HM09715 hitch level. These type bits are used for harder metal and will do a better job than just a steel or high-speed steel bit as they will dull…

view full answer...

Answer 2

Hello, and thanks for getting in touch. The etrailer Electric Trailer Jacks #e55ZV and #e23ZV will hold up just fine in cold weather. The housing is designed to be water/weather resistant. It even has a manual backup option if you were to lose power…

view full answer...

Answer 3

Hello Nathaniel, thanks for reaching out. So the etrailer jacks are going to be a great choice from a durability and affordability standpoint. The jacks offer all of the features you would want like a work light, sealed switches and a manual crank…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 8

Actually, the P3 now has the upgraded axis accelerometer like the P2. The Tekonsha P3 Trailer Brake Controller #90195, will work with both electric over hydraulic brakes on the trailer as well as electric brakes. It has a menu option on the display…

view full answer...

Answer 9

You're right, the mounting bracket is unique (in a good way) for the Curt TriFlex NEXT Trailer Brake Controller #C24VV. The bracket is smaller and all you do is put the included adhesive tape on the bracket and stick it wherever you like under…

view full answer...

Answer 10

Hey Mike! The etrailer Electric Trailer Jack #e55ZV would be a great replacement for the jack on your 2021 Jayco Jay Flight 242BHS. This has the same lift as your existing jack but with a higher 5,000 lb capacity making it a nice upgrade. It also…

view full answer...

Answer 11

Hey Bob. There's two possible locations for the brake controller port on your 2026 Ford F-150. The most likely one is on your dash behind the coin holder above the 4WD knob. It'll be connected to the back of the coin tray which is only…

view full answer...

Answer 12

Hey Bruce, we can help with everything you'll need to flat tow your 2026 Jeep Grand Cherokee with a Nighthawk tow bar part #RM-677. First thing you need is the correct base plate kit. If you have a Summit model you'll need part #RM97NQ, if…

view full answer...

Will Hopkins HM09175 Hitch Level Fit Thumb Latch Coupler

Continue Researching