Correct Replacement for Dexter Trailer Brake Assemblies 023-464-00

Question

Question:

Searching for matching assemblies for Dexter #023-464-00 thanks

asked by: Ralph L

0

Expert Reply:

The correct replacement for the Dexter Trailer Brake Assemblies 023-464-00 is the Dexter Nev-R-Adjust Electric Trailer Brake Kit part # 23-464-465.

expert reply by: Conner L

0

Answer 1

Yes you are correct the Replacement MaxxFan Plus 4-Speed Roof Vent with White Lid #MA00-04751KSX is the right replacement and measures 18 1/8" long and 16 1/2" wide, which is the same measurements as your current MaxxFan Plus Roof Vent w/…

view full answer...

Answer 2

If you have the wall control part #MA00A03550K installed in the wall of your trailer the Maxxair Fan part #MA00-04751KSX would easily integrate into it and work great. If you have a different switch setup let me know and I'll see what options you…

view full answer...

Answer 3

I would be happy to help! Since your Dexter axle has a 7000lb rating you will need the Electric Brake Assemblies #23-464-465 for self adjusting brakes, or #23-180-181 for standard brakes that you will need to adjust on occasion. I recommended the…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Correct Replacement for Dexter Trailer Brake Assemblies 023-464-00

Product Page this Question was Asked From

Continue Researching