Do Curt 5th Wheel Base Rails & Bracket Fit 2006 Dodge Ram 3500 Mega Cab

Question

Question:

Will the c16301-100 kit work for my 06 ram 3500 mega cab single rear wheel?

asked by: Clinton V

0

Expert Reply:

They sure do; I verified for you that the Curt 5th wheel base rails and brackets you asked about will fit your 2006 Dodge Ram 3500 Mega Cab. The correct part number is the following:

- Curt Semi-Custom Fifth Wheel Installation Kit for Dodge Ram 2500/3500 - Gloss Finish # C16301-100

expert reply by: Kyle S

0

Answer 1

I spoke with my contact at Reese and he informed me that there is nothing you can adjust on the slider that will allow you to remove that play. He did say to make sure that the pull pins that attach the slider to the rails are in correctly. You will…

view full answer...

Answer 2

For your 2012 Ram 3500 Long Bed 4x4, the brackets you need are Curt Custom, No-Drill Fifth Wheel Bracket Kit for Dodge Ram #C16420. This will work with the industry standard rails you referenced. Technically you shouldn't combine brands so I also…

view full answer...

Answer 3

I have a solution for you but the Curt item #C16427-104 will not fit your 2006 Dodge Ram 3500 Long Bed. Instead you will want the Curt Custom Fifth Wheel Installation Kit for Dodge Ram - Carbide Finish item #C16420-204. This kit is custom fit and…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

Hey Randy thanks for the information! Here are the parts you'll need to add a brake controller to your 2006 Dodge Ram 1500 with a factory 4-Way connector: Brake Controller and Custom Fit Wiring Harness - Curt TriFlex NEXT item #C43GV 7-Way…

view full answer...

Answer 11

We have lift kits for trailer that easily add 2 inches to the height of the trailer. For that you'd want the part #RR23QX and you'd be set. I attached a picture that shows how it installs to give you an idea. This would be the easiest…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Do Curt 5th Wheel Base Rails & Bracket Fit 2006 Dodge Ram 3500 Mega Cab

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching