Replacement Wet Bolt for Dexter E-Z Flex Suspension Kit

Question

Question:

I stripped a shoulder bolt that is part of the Dexter ez flex system. It is a wet bolt with a zerk fitting. Di you sell the bolts.

asked by: John P

0

Expert Reply:

We do have replacement wet bolts for your Dexter E-Z Flex Suspension Kit - Double-Eye Springs - Tandem Axle - 6,000 lbs # K71-652-00. What you need is the Step Wet Bolt for 1-3/4" Double Eye Springs # 34007-187-00.

expert reply by: Robin H

0

Answer 1

Hey Ian, great to hear from you again! The differences between the MORryde CRE3000 #MR87ZR and AllTrek 4000 #MR89DR that fit a 33" wheelbase is the height between the hanger and equalizer bolts, and the amount of travel the suspension style will…

view full answer...

Answer 2

According to the installation instructions from Dexter Axle the torque specs for the wet bolts on their Dexter E-Z Flex Suspension Kits, like part #K71-653-00, is 30 - 50 ft-lbs. I have attached a clip from their instructions for you to check out.

view full answer...

Answer 3

Hey Leonard, thanks for reaching out to us. Yeah sometimes the fitguide isn't great for all RVs since those are a little trickier to confirm suspension parts etc. Manufacturers like to change part up frequently so it's difficult to keep up…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 12

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Replacement Wet Bolt for Dexter E-Z Flex Suspension Kit

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching