Can MORryde Jerry Can Mount be Installed on Swing-Away Arm

Question

Question:

Hi Would this work MORryde Jerry Can Mount for Jeep Wrangler TJ and YJ - Driver or Passenger Side Item # MR69MR if I use a Wilco Offroad Hitchswing Or the Saris Swing Away I have a Tacoma 2015 and would use the can holder in the swing arm hitch. Thanks

asked by: Nicolas D

0

Expert Reply:

The MORryde Jerry Can Mount for Jeep Wrangler TJ and YJ # MR69MR has a 2" shank so it will fit perfectly with either the Wilco Offroad Hitchswing or the Saris Swing Away Hitch Extender # SAR36VR.

I recommend the Saris over the Wilco simply because it has a few extra connection points so you have more peace of mind about the swing-arm being secure while you're driving around.

Attached are some review videos for you to check out.

expert reply by: Jon G

0

Answer 1

Hello Jay, I’m curious what panel you’re planning to use. How many panels will you be running, and what is the total wattage? I want to make sure the controller I recommended is properly sized for your setup. Right now, your camper has the Go Power…

view full answer...

Answer 2

Hi Brad; thanks for pointing this out. I reached out to MORryde and can confirm that the #MR69MR will fit a 2" receiver. I'm not sure where that other information came from saying it wouldn't fit any receiver size, but the part that…

view full answer...

Answer 3

As long as you have at least 6" of clearance from the center of the hitch pin hole for the OEM hitch to the rearmost part of your 2021 Jeep Grand Cherokee you can definitely use the MORryde Jerry Can Mount #MR69MR for your 2" hitch…

view full answer...

Answer 4

Hey Cathy, sweet camper! I really like the Rhino-Rack Aero Bar Roof Rack for Camper Shells #Y02-500B-ST you were looking at because it's a tried-and-true solution that also gives you tracks so you can accommodate a variety of different load…

view full answer...

Answer 5

Yes you could use just the carrier and shank of the Fender Mounted Jerry Can Holder for Jeep Wrangler TJ and YJ #MR69MR in the hitch of your 2018 Jeep JL Unlimited if you wanted to. This comes with basically a hitch that attaches to the frame but you…

view full answer...

Answer 6

I reached out to my contact at Morryde to verify, and yes the Fender Mounted Jerry Can Holder for Jeep Wrangler TJ and YJ - 5 Gallon - Tall Tray #MR69MR can be used on a standard 2" receiver like you have on your Jeep. Keep in mind, there is…

view full answer...

Answer 7

Hey Eric, the Swagman Swivel Hitch Extender part #S86SR would definitely work for you. It actually has an open back on the backside of the hitch opening so there wouldn't be any hitch pin issues.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 10

Congratulations on the HHR purchase James and thank you for sending the photo! Based on what I can see, your base plate appears to use Blue Ox's tabs and looks very similar to the Blue Ox Base Plate Kit #BX1692 used on the 2006-2011 Chevrolet…

view full answer...

Answer 11

John, that is a completely valid concern, especially since you already went through the trouble of switching from the horizontal air distribution box to the lateral version just to improve airflow throughout your R Pod. The last thing you want is to…

view full answer...

Can MORryde Jerry Can Mount be Installed on Swing-Away Arm

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching