Replacement Converter for Progressive Dynamics Panel PD4560K12LS8

Question

Question:

Do you still recommend the PD4560LICSV as a replacement for the PD4560K12LS8?

asked by: Greg Z

0

Expert Reply:

Yes, the replacement converter part # PD4560LICSV is the correct lithium battery compatible option for the PD4560K12LS8 that you referenced. If the battery isn't lithium you'd instead need the # PD4560CSV.

expert reply by: Jameson C

0

Answer 1

The Progressive Dynamics REL 60A 4500 Series Inteli-Power Converter Section #PD4560CSV is designed for lead acid batteries, but a jumper can be installed to make it compatible with lithium as well. Progressive Dynamics has a great step by step…

view full answer...

Answer 2

When you installed your Progressive Dynamics RV Power Control Center #PD4135K did you insert your DC fuses into the ports to complete the DC side of the installation? If you did I recommend doublechecking that they haven't been blown. There's…

view full answer...

Answer 3

The Progressive Dynamics #PD4560K18LS8 is a power center which includes a converter/charger for lead acid or lithium batteries. The converter control board has a tiny switch on it that can be set to "LI" for lithium or "LA" for…

view full answer...

Answer 4

Hey Brandon, The Progressive Dynamics #PD4560LICSV has a lithium jumper on the circuit board that is most likely in the 'WIZ' position instead of in the 'LI' position. In the WIZ position this converter section will utilize the charge…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Replacement Converter for Progressive Dynamics Panel PD4560K12LS8

Products Featured in This Question

Continue Researching