Replacement Grease Seals For a 1992 Fleetwood Wilderness 22H With 2,800LB Axle

Question

Question:

need bearing seals for two 2800# axles, ser# 5235354 on one of them. inner bearing # KLM 67048 no # on smaller outer bearing. Drum is 10x2 brake shoes are 1 1/2 wide. seals are 2 5/16 OD and 1 3/4 id hope thats enough info thanks

asked by: Mike M

0

Expert Reply:

Based on your measurements for the grease seal it appears Seal # 10-42 is the correct size for your axles. This seal is 1.750 inner diameter and 2.33 outside diameter and they are for Dexter 2,800lb axles.

expert reply by: Bud M

0

Answer 1

The Redline Grease Seal item #10-42 is going to be the closest seal we have to your measurements of 2.335 OD and 1.789 ID. The .03 difference could be caused by a measuring issue like your caliper being off by a small amount. If not the seal has some…

view full answer...

Answer 2

Based on previous information we have for your UFP HD-1377-10 hub it uses the following components. I do recommend pulling one of your hubs to verify that the replacements listed below match your current parts. Inner Bearing #L68149 (Inner diameter…

view full answer...

Answer 3

Based on the information you provided, the #10-42 grease seal is the correct one for your application on the now obsolete Dexter 8-283 hub for 2,800 lb axles. To install it, with the inner bearing in place, set the grease seal over the top and press…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 8

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 11

Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 #TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I…

view full answer...

Answer 12

Hey Thomas, in the Timken bearing kit part #TMK52VR the race that corresponds with the inner bearing L68149 is L68111. Do you have a 3,500 lb trailer axle?

view full answer...

Replacement Grease Seals For a 1992 Fleetwood Wilderness 22H With 2,800LB Axle

Product Page this Question was Asked From

Continue Researching