Replacement Fan-Tastic Roof Vent Lid for LF8000 Assembly

Question

Question:

I have a 2004 regal prowler 5th wheel fan tastic vent dated 10/03, model LF8000, i am looking for a new vent cover, hinged at rear and slide up bar on right side if looking from the front

asked by: Wayne

0

Expert Reply:

Looks like the correct replacement vent lid you would need is the part # FVK1020-19. This is the correct replacement vent lid for Fantastic roof vents like your LF8000.

expert reply by: Jameson C

0

Answer 1

When it comes to replacing your Fan-Tastic Vent #LF8000 The Fan-Tastic Vent Roof Vent #FV803350 would work for you. The fan has 3 manual speeds that lets you boost or reduce airflow as needed. It has Rain sensor that will signal the dome to close…

view full answer...

Answer 2

There is not a fuse we carry for the 8000 Series of Fan-Tastic vent. It does use a 4 amp slow blow fuse so to make fuse access simpler you can use In-Line Fuse Holder #C58470-1 and if you need to replace the bow-tie bracket, motor, and blade the…

view full answer...

Answer 3

Yes, the Progressive Dynamics part #PD9260C will work great as a replacement for the Magnetek 900 series model 950 that you have currently.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

You can use the RV Propane Gas Detector #RS64FR (white) or #RS44FR (black) to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Replacement Fan-Tastic Roof Vent Lid for LF8000 Assembly

Product Page this Question was Asked From

Continue Researching