P-Trap Fitting For A Shower/Tub That Has A 1-1/4 Diameter Pipe

Question

Question:

I have a 2011 Lance trailer that needs to have the shower/tub P trap replaced. It appears to be 1 1/4, but most traps are 1 1/2. Lance no longer supports end users buying parts, wondering if you can help me with parts or directing me to where I could find the part Im looking for. Thanks for the help.

asked by: Tim W

0

Expert Reply:

I believe we have what you're looking for.

We have the P-Trap Fitting # LSB86XR, which will install under your sink, shower or tub and will fit onto 1-1/4" to 1-1/2" diameter pipes.

expert reply by: Bryce D

0

Answer 1

For the Replacement 3-Speed Switch for Fan-Tastic Vent Roof Vent, part #FVK1031-05, the left terminal (B) is for the battery, the upper right (C) is for the circuit board, and the lower right (M) is for the motor. Refer to the picture below. The…

view full answer...

Answer 2

Yes, John we sure do! To replace the fuses in your FanTastic Vent Fan you will need the Replacement 4 Amp Slow Burn Fuse Kit for Fantastic Fans item #DMC57FR you were looking at. This comes with two fuses that measure 1-1/4" x 1/4". The…

view full answer...

Answer 3

I believe we have exactly what you're looking for. I went out to the warehouse and personally measured the LaSalle Bristol P-Trap Fitting for RV Sewer System #344633211N and measured 3-1/2" from the middle of the fitting to the first bend in…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 10

Hello Matt, I was seeing some mixed information on this as well, so I reached out directly to my contact at Firestone to confirm. The Firestone Ride-Rite Air Bags w/ Easy Mount Compressor - Wireless Control - Single Path - 5,000 lbs #F44XV will fit…

view full answer...

Answer 11

Hello Jeff, Sounds like you’ve got a big camper (about 4,000 lbs) on your 2024 F-350 dually, and when it’s loaded, the truck feels bouncy and sways a bit. That’s pretty common with heavy campers, especially if the suspension is still stock.…

view full answer...

Answer 12

We sure do Mike! To add a set of air bags and a compressor to your 4WD 2019 Ford F-350, I recommend the Firestone item #F44XV. This kit comes with a set of 5,000 lbs capacity air bags that will level out the rear end of your F-350 when you are towing…

view full answer...

P-Trap Fitting For A Shower/Tub That Has A 1-1/4 Diameter Pipe

Product Page this Question was Asked From

Continue Researching