Grease Seals Needed for a Weekend Warrior Triple Axle Trailer with 6000 Pound Axles

Question

Question:

Hello. I recently purchased drum and electric brake units from Etrailer. When I install them, I want to have the correct axle seals on hand. We have a triple axle, 2007 Weekend Warrior 32ft. It has AL-KO 6000 lb axles with the 12x2 electric drum brakes. Can you tell me which seals I need? Thank you.

asked by: Eric H

0

Expert Reply:

The best way to determine the correct grease seals for your triple axle trailer would be to take a few precise measurements. I recommend using a set of digital dial calipers to obtain these measurements.

You will need to measure the grease seal portion of the spindle as well as the diameter of the hub to determine the correct grease seal for your triple axle trailer. I have included a diagram showing these measurement locations for you.

I have included a video and a helpful article that you might find useful for installing your grease seals.

expert reply by: Rachael H

0

click to enlarge

Robert

3/16/2020

I have 2008 weekend warrior toy hauler that had Al-Ko 6000lbs axles. 12\12 electric brakes. I sheared of the 4 out of the 6 studs. Can I replace the studs or have to replace the whole hub? Part# please. Thank you

Chris R.

3/17/2020

I'd definitely replace the entire hub/drum assembly on your trailer. The studs aren't available by themselves and there's also a decent chance that the existing hub also took some damage. For the 6,000 pound Al-KO axles the etrailer # AKHD-655-6-EZ-K should work perfectly. Just be sure your current hub uses the 25580 inner bearing and 15123 outer bearing.

Helpful Links

Trailer-Hubs-and-Drums/Dexter-Axle/42656.html

Answer 1

One common grease seal size for a 6,000 lb axle has an inner diameter of 2.25" and outer diameter of 3.376" just like the #RG06-070. More than likely this matches what you have now, but you can't be 100% sure without either measuring or…

view full answer...

Answer 2

The Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles - 12" - 5 Spoke Utility #8-174-5UC3 is the only hub that is compatible with those bearing inner diameters. This uses #15123 which have the same inner diameter as the #14125A,…

view full answer...

Answer 3

First you will need to remove the old hydraulic equipment. Remove the surge coupler or actuator, remove all the lines, and finally remove the brake assemblies. If you have 10 inch diameter hub and drums, you may need to replace those as well. If you…

view full answer...

Answer 4

It appears that the HydraStar Disc Brake Kit #HSE7K-T1 is the correct kit for your 2021 Vanleigh Vilano 320GK. To verify this you can find the axle serial numbers and send that information to me so I can verify all the components are correct.…

view full answer...

Answer 5

If you're getting a fault with your Atwood RV Carbon Monoxide and Propane Gas Detector #AT36681 then I would first ensure that there's no presence of propane and then would cut power to the detector for a few minutes to let it fully power…

view full answer...

Answer 6

My contact at Atwood advised that the light under the "Propane" label blinking red indicates the propane detector is disabled. The blinking indicates that the sensor is worn out and the unit should be replaced with #AT36681. For reference…

view full answer...

Answer 7

The red blinking light on the light of the Atwood RV Carbon Monoxide and Propane Gas Detector AT36681 typically means that the propane sensor is disabled or faulty. Since you've already tried resetting the unit you'll want to make sure you…

view full answer...

Answer 8

The difference between the 10-10 grease seals, #RG06-090, and the 10-36 grease seals, #RG06-070, is their inner diameter. The 10-10 grease seals fit older spindles with a seal journal (see photo) diameter of 2.125 inches. The 10-36 grease seals fit…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Grease Seals Needed for a Weekend Warrior Triple Axle Trailer with 6000 Pound Axles

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching