Replacement Side Rails For Retrax MX Series Tonneau Covers On A 2020 Ram 2500

Question

Question:

Will these rails work for a foot bed without cut outs

asked by: Chuck C

0

Expert Reply:

Yes, the Replacement Side Rails for Retrax MX Series Hard Tonneau Covers # RT82232 will fit your 2020 Ram 2500 if you have a 6-1/2' bed without the RamBox.

This will fit if you have the RetraxONE MX # RTT-60232, RetraxONE XR # RTT-70232, RetraxPRO MX # RTT-80232, PowertraxPRO MX # RTT-90232 tonneau covers.

expert reply by: Bryce D

0

Answer 1

Yes, you can replace the side rails on a RetraxONE MX Hard Tonneau Cover with the RetraxONE XR Hard Tonneau Cover Rails to gain the t-slots. For a 2016 Ram 2500 6-1/2' bed you'll need the Replacement Side Rails for Retrax XR Series Hard…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 5

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 8

Hey Kelvin, welcome back. To flat tow a 2026 Ford Maverick with your Demco Commander II Tow Bar item #DM9511012, I recommend the following parts: Baseplate Kit - Demco Tabless Base Plate Kit item #DM38CV Wiring Harness - Roadmaster Diode 7-Wire to…

view full answer...

Answer 9

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 10

Hey Patrick, thanks for the measurement. The Travel Door Latch for GE Appliances RV Refrigerator item #GE98FR has mounting holes 1-3/16" on center. It's designed for the 9.8 Cu. Ft. GE Appliances RV Refrigerator with Top Freezer item #GE58FR…

view full answer...

Answer 11

Hey Bill! The Rebel is the heavier duty SumoSprings jounce springs and they have the higher weight rating at 3,000 lbs #SS64VR or 5,000 lbs #SS27GR. I usually only recommend these heavy duty versions if you have a lot of weight in the truck bed or on…

view full answer...

Answer 12

I spoke with my contact at Trailair and from your serial number we were able to determine that your trailer came with a 1621 HD pin box which is a long pin box style. I was unable to obtain the exact part number for your Trailair pin box but from the…

view full answer...

Replacement Side Rails For Retrax MX Series Tonneau Covers On A 2020 Ram 2500

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching