Replacement Bearing Kit For 1" BT8 Trailer Spindle

Question

Question:

Hello, My spindle measures 0.99 inches where the bearings ride and 1.22 inches where the grease seal rides. What bearing kit should I get? Thanks

asked by: Lindsey

0

Expert Reply:

It sounds like you need the Bearing Kit for 1" BT8 Spindle # BK1-100. This bearing kit uses Inner and Outer Bearings # L44643 that measure 1" on the inside diameter and a Grease Seal # 34823 with inner diameter of 1.249". These are the closest components we have to your spindle measurements.

expert reply by: Bud M

0

Answer 1

Yes, the L44649 bearings for a 1-1/6" spindle will have the same outer diameter (1.980") as the L44643 bearings for a 1" spindle so you can obtain the Bearing Kit for 1" BT8 Spindle part #BK1-100 to reuse your hubs.

view full answer...

Answer 2

It is likely you can use the Trailer Idler Hub Assembly for 3,500 lb Axles #AKIHUB-5475-35-K as it has the most common bearing and seal for 3,500 lb axles, but you'll need to verify this as we don't have any way of knowing the exact hubs that…

view full answer...

Answer 3

The best way to find out what kit you need is to find the bearing numbers which should be stamped on the bearing themselves. You will also need to know the grease seal, whose inner and outer diameter you will need to measure with a digital caliper to…

view full answer...

Answer 4

In order to find the correct bearings and seals for your Shoreline boat trailer you will need to identify what you have. The first thing I would check is the axle tag. If this was made by an existing manufacturer like Dexter or Lippert they will be…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Replacement Bearing Kit For 1" BT8 Trailer Spindle

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching