Is The Durabuilt Hammer Lock Coupling Link For 1/2 Chain Sold As A Pair Or Individually?

Question

Question:

regarding Item # DU96MR - are these sold per each or per pair? Thanks.

asked by: Keith

0

Expert Reply:

The Durabuilt Hammer Lock Coupling Link for 1/2" Chain # DU96MR you mention, is sold as a two halves equaling 1 link, weighing 1.4-lbs total.

I have also attached a review video for you to check out.

expert reply by: Bryce D

0

Answer 1

Hey Alex, I agree that Draw-Tite beefs up their safety chain loops quite a bit compared to most manufacturers so I went out to the warehouse and test-fit the Durabilt Safety Chain Connectors #DU35QR on the loops of the #41944 and found that they are…

view full answer...

Answer 2

The 12,000 lb weight rating of the Durabilt Safety Chain Connectors #DU35QR is individually as well as both of them. It's a little confusing, but essentially you don't double the weight rating of these types of connectors when more than one…

view full answer...

Answer 3

It sounds like you're needing some safety chain keepers. We offer those as part #CE16691A.

view full answer...

Answer 4

Hey Anthony, If you're referring to the little spring/clip I have pictured below then it would not be something that we offer. The #CE16691A you were looking at would be the only alternative we could offer besides replacing the entire hook.

view full answer...

Answer 5

The clevis hook on the Tow Ready Safety Chain Kit part #49150 is 5/16" diameter. Therefore if this hook will not work with the Curt Ball and Safety Chain Loops Kit for Ram Underbed Gooseneck Hitch part #C60618 then you will want to move up to a…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Is The Durabuilt Hammer Lock Coupling Link For 1/2 Chain Sold As A Pair Or Individually?

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching