Gauge of Wire in the SmartPlug RV Power Cord part # SM36FR

Question

Question:

WHAT IS THE GAUGE OF THE WIRE AND IS IT 100 COPPER?

asked by: JOHN

1

Helpful Expert Reply:

I checked with SmartPlug and they stated that the RV Power Cord part # SM36FR that you referenced has 10 gauge wires and the core is 100 percent copper.

expert reply by: Jameson C

1

Answer 1

Hey Richard, this would be powering a 50 amp camper off 30 amps, so this would be less amperage not more. However plugging into 30 amps means half of their panel gets zero power, and the other half gets 30 amps instead of 50, so you should stick with…

view full answer...

Answer 2

Thanks for reaching out, Glen! To get the plug side of the SmartPlug RV Power Inlet - 50 Amp #SM56FR you were looking at, you just need the 50 Amp Female Plug Assembly #SM36FR.

view full answer...

Answer 3

Currently SmartPlug only offers their 50 amp cord in a 30' Length #SM86FR. We do have a Replacement End #SM36FR you could attach to a 50 Amp Power Cord #A10-5025END. This particular cord is 25' but you can cut it down before adding on the…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Gauge of Wire in the SmartPlug RV Power Cord part # SM36FR

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching