Roof Sealant Recommendation For Enclosed Trailer

Question

Question:

I have an enclosed trailer with a plastice top transition piece connecting the front of the trailer and the metal roof. What type of sealant would you recommend for the roof seam?

asked by: Steven Q

0

Expert Reply:

A great option is the TremPro 644 Silicone Sealant # 0160297. This sealant does a great job holding up to temperature changes without shrinking, drying out or cracking. This silicone is white but can be painted to match your trailer. Additionally, this sealant will work great with various materials, such as, metal, wood and plastic.

expert reply by: Bryce D

0

Answer 1

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 2

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 5

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 6

Yes, the puck system used on the 2016-2019 Chevy/GMC trucks is different than the pucks used on the 2020 and newer trucks. So you would need a 5th wheel like the B&W Companion #BWRVK3710 for your 2020 GMC Sierra 3500 with an 8' Bed. If you…

view full answer...

Answer 7

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 8

Hi McKay, I'm a bit confused on what you're asking but I think it's the size of the hole the gooseneck ball fits into on the Custom Underbed Installation Kit for B&W Companion 5th Wheel Trailer Hitches #BWGNRK1020-5W. This is a 2-1/2…

view full answer...

Answer 9

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...

Answer 10

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 11

The most likely cause of the "no signal" error you are receiving with the Furrion Vision S Wireless RV Backup Camera System part #FOS43TASF is due to an interruption on the camera's power wire. Make sure that the camera is receiving…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Roof Sealant Recommendation For Enclosed Trailer

Featured Help Information

Miscellaneous Media

Continue Researching