Replacement Wheel Stud and Correct Lug Nut For Dexter Trailer Hub and Drum Assembly # DX78QR

Question

Question:

Do you sell the studs separately? And what nuts fit this hub,

asked by: Thom O

1

Helpful Expert Reply:

Yes, the Replacement Wheel Stud # DX97XR is the correct fit for your Dexter Trailer Hub and Drum # DX78QR.

The Dexter Lug Nut # 6-118 is the correct size(M22 x 1.5) for the wheel stud on the hub.

expert reply by: Bud M

1

Answer 1

As long as your dual wheel has a flat surface where the Flange Wheel Nut #95188 would rest against, like what the Dexstar Dual Wheel #AM20790 has, then you would use this flange wheel nut in the place of a nut with a 90 degree cone. Attached is a…

view full answer...

Answer 2

The Gooseneck to 5th Wheel Trailer Coupler Adapter - Inner Tube - Round - 25K lbs Item #KPG5-R25-IP is designed as an adapter for goose neck trailers with a 4" round tube. As long as your Big Tex trailer has a 4" round tube this adapter is…

view full answer...

Answer 3

For your Big Tex 90PI trailer, I recommend checking out the: -RC Manufacturing T-Series Trailer Tongue Tool Box #350980. This toolbox has a cargo capacity of 2.6 cubic feet, measures 30" long x 14-1/2" tall x 14-1/2" wide, and is…

view full answer...

Answer 4

There are a few options but the Westlake 215/75R17.5 Radial Tire w 17-1/2" Lynx Aluminum Wheel #LHAS701 will not fit the 5/8" studs on your trailer. You can change your hubs to ones with a 9/16" studs to use these wheels. To do this I…

view full answer...

Answer 5

Hi Johnny, Your Big Tex 25GN should have Dexter 12,000 lb axles, and if so the correct spindle nut is the Replacement Trailer Spindle Jam Nut #DX88QR.

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Replacement Wheel Stud and Correct Lug Nut For Dexter Trailer Hub and Drum Assembly # DX78QR

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching