Axle Nut For Big Tex 25GN Trailer With 12k Dexter Axles

Question

Question:

I am looking for the axle nut for a Big Tex 25 GN trailer. Can you help with this?

asked by: Johnny S

0

Expert Reply:

Hi Johnny,

Your Big Tex 25GN should have Dexter 12,000 lb axles, and if so the correct spindle nut is the Replacement Trailer Spindle Jam Nut # DX88QR.

expert reply by: Kyle S

0

Johnny

7/23/2024

Thank you for your help.

Answer 1

The Gooseneck to 5th Wheel Trailer Coupler Adapter - Inner Tube - Round - 25K lbs Item #KPG5-R25-IP is designed as an adapter for goose neck trailers with a 4" round tube. As long as your Big Tex trailer has a 4" round tube this adapter is…

view full answer...

Answer 2

For your Big Tex 90PI trailer, I recommend checking out the: -RC Manufacturing T-Series Trailer Tongue Tool Box #350980. This toolbox has a cargo capacity of 2.6 cubic feet, measures 30" long x 14-1/2" tall x 14-1/2" wide, and is…

view full answer...

Answer 3

Yes, the Replacement Wheel Stud #DX97XR is the correct fit for your Dexter Trailer Hub and Drum #DX78QR. The Dexter Lug Nut #6-118 is the correct size(M22 x 1.5) for the wheel stud on the hub.

view full answer...

Answer 4

There are a few options but the Westlake 215/75R17.5 Radial Tire w 17-1/2" Lynx Aluminum Wheel #LHAS701 will not fit the 5/8" studs on your trailer. You can change your hubs to ones with a 9/16" studs to use these wheels. To do this I…

view full answer...

Answer 5

Hey Mike, thanks for the information! The best weight distribution system for your 7,000 lbs Big Tex 70DM car hauler is going to be the Equal-i-zer item #EQ37100ET. This system works with tongue weights between 600 lbs - 1,000 lbs. That's going…

view full answer...

Answer 6

The Dexter hub you referenced, 8-201, is a 5,200 lb hub, though a 5 on 4-1/2 bolt pattern does not come on 5,200 lb hubs. The correct bearings for the 5,200 lb hub are #25580 and #LM67048, while the proper races are #25520 and #LM67010. I have…

view full answer...

Answer 7

The brake wire providing voltage is wired in parallel, with one lead from each magnet being grounded to the trailer frame. We have a great Wiring Help Page that shows a diagram, I will provide a link to it below.

view full answer...

Answer 8

On Redline Wheel Cylinder #BP17-030 the brake line fitting is standardized, 3/8-inch with 24-TPI (24-threads per inch). I confirmed with my contact at Redneck.

view full answer...

Answer 9

According to the instructions for the Bulldog Velocity Series Electric Landing Gear Jack #BD185400 there are 2 ways to install this jack; you can either use at least four 1/2" grade 5 bolts, or four U-Bolts. There are no adapters to make this…

view full answer...

Answer 10

I believe we can narrow this down based on the information you are referencing. However, the best way to be sure is to measure your existing bearings or spindle with a digital caliper like the #PTW80157. It looks like one bearing is stamped with…

view full answer...

Answer 11

We do offer a range of replacement trailer hub assemblies that use the L68149 bearing as their inner bearing and that have the 5-on-4-1/2-inch bolt pattern. All can be seen on the link at right. However, none of these 16 hubs uses that same bearing…

view full answer...

Axle Nut For Big Tex 25GN Trailer With 12k Dexter Axles

Product Page this Question was Asked From

Continue Researching