What All Is Needed To Attach A Brake Controller To A 2021 Ford E350 Cutaway Sunseeker

Question

Question:

Unit has 7 port plug on back but I am told it is not wired for brake controller. What would you suggest?

asked by: Joseph J

1

Helpful Expert Reply:

From everything I could find, your 2021 Sunseeker should actually be pre-wired for a brake controller. Especially since you have a 7 Way already on the back. This may be different on your model, but typically you will just access the brake controller connector behind the coin tray to plug the # 3034-P pigtail into. You can then mount the Tekonsha Prodigy P3 # 90195 in the place that suits your needs and you are good to go.

With that said, if something weird was done, you may need to run a wire from the blue brake output side of the controller to the 5 o'clock position on the 7 Way. Usually this will only need to be done if there was not a 7 Way already on the vehicle though, so you should not need to do this.

expert reply by: Lazer S

1

Answer 1

I would be happy to help you find the right connector. It is behind the dash at the very top of your console on your 2019 Ford E-350. You will need to pop that panel out and the connector you are looking for will be plugged into the insert. I have…

view full answer...

Answer 2

Since your 2013 Toyota Tacoma has a factory tow package, including a 7-way connector at the back bumper, it will have a brake controller connector. While it is usually visible above the emergency brake pedal, it may sometimes be taped or zip-tied to…

view full answer...

Answer 3

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 4

If your 2013 Toyota Tacoma came with a factory brake controller port then the rest of the wires you need to hook up to the 7-way (12 volt power and brake output) should already be ran to the rear of the vehicle, under the bumper and near the spare…

view full answer...

Answer 5

I can help you understand your 2016 Toyota Tacoma a little more and help you install that Tekonsha brake controller. Since your Tacoma doesn't sound like it came with the factory 7-way then you will not have a plug in location for your brake…

view full answer...

Answer 6

For your 2013 Toyota Tacoma and a Tekonsha brake controller the correct brake controller wiring harness is #3040-P. In plugs into a plug on the truck located under the dash to the left of the emergency brake pedal. Some times the factory plug can…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hey Melanie. The reason you can't find a replacement for your GE ARC15AACBL2 15,000 btu air conditioner is because they phased them out. In 2025 all RV AC systems had to change over to a new coolant called R32. This was a EPA mandated decision.…

view full answer...

What All Is Needed To Attach A Brake Controller To A 2021 Ford E350 Cutaway Sunseeker

Featured Help Information

Miscellaneous Media

Continue Researching