Replacement Mount for etrailer Round, Pipe Mount Swivel Jack

Question

Question:

I need the round weld on part that fits jack TJP-5001S-B can you tell me the part number please? Thanks

asked by: Todd A

0

Expert Reply:

The correct replacement male pipe mount for the Round, Pipe Mount Swivel Jack part # TJP-5001S-B is the Round, Pipe Mount Swivel Jack part # TJP-IP916.

expert reply by: Conner L

0

Answer 1

Pro Series Round, Pipe-Mount Swivel Jack #PS1401420303 is a potential option for you. Please note that it does come with the pipe that gets welded onto the trailer. That pipe has an outer diameter of 2 inches. The 2-1/2 inch outer diameter mating…

view full answer...

Answer 2

The Round, Pipe Mount Swivel Jack #TJP-5001S-B uses a 5/8" Diameter Pull Pin #TJP-PN58. The jack slides onto a 2" diameter weld on pipe that is included.

view full answer...

Answer 3

Hey Martin, The Replacement Male Pipe for Curt Pipe Mount Swivel Jacks #C46FV has a 2" outer diameter which is pretty standard for pipe-mounted swivel jacks so it would likely be a fit. I wasn't able to confirm the female side of this on the…

view full answer...

Answer 4

The length of the pipe itself (the round mount) is 2-1/4 inches for the Round, Pipe Mount Swivel Jack w/ Footplate - Weld On - Sidewind - 10" Travel - 3,000 lbs #TJP-5001S-B. I can't tell you for certain though whether it is long enough to…

view full answer...

Answer 5

The Pro Series Round, Pipe-Mount Swivel Jack w/ Footplate - Sidewind - 10" Lift - 2,000 lbs #PS1401060303 has an overall length when retracted of 16-5/8 inches. This jack does not have a wheel. For a similar jack with a wheel, I recommend the…

view full answer...

Answer 6

The overall height of the Round, Pipe Mount Swivel Jack #TJP-5001S-B is 16-3/4 inches when fully retracted and 26-3/4 inches when extended. Basically from the center of the pipe mount to the top of the jack measures 6-1/2 inches.

view full answer...

Answer 7

The Pro Series Round, Pipe-Mount Swivel Jack w/ Footplate - Sidewind - 10" Lift - 5,000 lbs #PS1401420303 has a 10-1/2 inch dimension from the center of the mount but is only 6-1/2 inches from the center of the mount to the top of the unit. This…

view full answer...

Answer 8

We have just the thing! The Replacement Male Pipe #TJP-IP916 is going to be the correct weld-on male pipe mount for the #TJP-5001S-B jacks. If you need the female side to weld to the jack itself it will be part #TJP-OP916.

view full answer...

Answer 9

The 10-1/2 inch measurement that you referenced is the distance from the bottom of the foot bracket to the center of the mounting bracket. I went out and measured it and shot a little video for you as well that I attached.

view full answer...

Answer 10

There is roughly 1/2" of exposed inner tube on the Round, Pipe Mount Swivel Jack #TJP-5001S-B exposed the bottom of the outer tube. This will give you a length of 9-3/4" from the center of the pipe mount to the bottom of the tube.

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Replacement Mount for etrailer Round, Pipe Mount Swivel Jack

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching