Could Road Armor Equalizers # LC696740 Fit 2020 Grand Design Imagine XLS 22MLE

Question

Question:

Will these work on a Grand Design Imagine XLS 22MLE trailer? thanks,

asked by: Chris

0

Expert Reply:

Since we know your Grand Design Imagine XLS 22MLE has 3,500 lb axles the Road Armor Shock Absorbing # LC696740 will work in that regard. You'd need to measure the distance between the mounting holes of your current equalizers but as long as they are close to 6 inches and vertically between the lower holes and upper holes the dimension is close to 3-1/2 inches you'd be set.

expert reply by: Jameson C

0

Answer 1

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 2

Hey Joseph! That is a 3,500 lb Lippert axle so you can use the Hub Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle #BK2-100. If you prefer a Timken kit made in the USA the #TMK52VR is also available. Both come with…

view full answer...

Answer 3

The RoadActive Suspension system #RAS34FR effects the suspension, so it will work with any body lift that you may have in place. The RAS system will lift the rear of the vehicle approximately 1" to 1-3/4" depending on the truck, so the bed…

view full answer...

Answer 4

Grease Seal #RG06-050 is the replacement part for the Dexter 010-019-00. It is 1.719 inches inner diameter and 2.565 inches outer diameter. It is a fit for 3500 lb axles. This is a confirmed replacement cross-reference.

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The Road Armor Shock Absorbing Equalizer Kit part #LC696740 are taller than most other standard equalizers so you'll likely need the longer 3-1/8" shackle straps when using them, the Lippert AP Kit part #LC52SV is a go-to for this as it has…

view full answer...

Answer 7

For your 2021 Grand Design Imagine 22RBE XLS I recommend the Dexter E-Z Flex Equalizers #K71-653-00. The best upgrade option is typically the one that matches your current equalizers. You have standard Dexter 7-3/4" equalizers right now so these…

view full answer...

Answer 8

According to my research your 2023 Grand Design XLS 23LDE should have tandem 3,500 lb axles in an "underslung" (leaf springs below the axles) configuration. This means you need two of the following SumoSprings kit: - SumoSprings Trailer…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

You can use the RV Propane Gas Detector #RS64FR (white) or #RS44FR (black) to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...

Answer 12

Thanks for the picture! I checked with Progressive Dynamics the replacement power converter you need for your Parallax Series 7300 Model 7345 is the Replacement Converter for Parallax/Magnetek or WFCO RV Power Centers - 45 Amp item #PD4645V.

view full answer...

Could Road Armor Equalizers # LC696740 Fit 2020 Grand Design Imagine XLS 22MLE

Continue Researching