How is Different Gears Selected on Bulldog 2-Speed Jack # BD183401

Question

Question:

Been trying to do some research with no luck. Looking for the operation of the two speed planetary gearbox more specifically how do you change between high and low gears.

asked by: Matt B

0

Expert Reply:

To change gears on the Bulldog 2-Speed Jack # BD183401 that you referenced you would push in/pull out on the shaft. This is how you go between the two speeds.

expert reply by: Jameson C

0

Answer 1

We do have the Bulldog 2-Speed Jack #BD183401 without a spring return. This is a 10,000lb lift capacity 2-speed jack similar to the etrailer #TJD2SP-12000SP-F jack you found. The Bulldog requires a separate Handle #BD701466 as one is not included. We…

view full answer...

Answer 2

It sounds like you have the older Fulton 12K Magnum Series HD Jack. Since there isn't a way to convert this to an electric jack you'll need to replace the entire jack. To get to your end result of having an electric jack for your horse…

view full answer...

Answer 3

Yes, for a Bulldog 12,000 lb static (10,000 lb lift) capacity we have the following jacks for you: Bulldog 2-Speed Jack - Drop Leg w/ Spring Return - Planetary - 26" Lift #BD183816 (front facing plunger pin) Bulldog 2-Speed Jack - Drop Leg w/…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 10

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

How is Different Gears Selected on Bulldog 2-Speed Jack # BD183401

Continue Researching