Availability of Bulldog 12,000 lb 2-Speed Trailer Jack

Question

Question:

Do you guys carry a bulldog 12K to speed leg Jack

asked by: Phil B

0

Expert Reply:

Yes, for a Bulldog 12,000 lb static (10,000 lb lift) capacity we have the following jacks for you:

Bulldog 2-Speed Jack - Drop Leg w/ Spring Return - Planetary - 26" Lift # BD183816 (front facing plunger pin)
Bulldog 2-Speed Jack - Drop Leg w/ Non-Spring Return - Planetary - 26" Lift # BD183416 (front facing plunger pin)
Bulldog 2-Speed Jack - Drop Leg w/ Non-Spring Return - Planetary - 26" Lift # BD183401 (side facing plunger pin)
Bulldog 2-Speed Jack - Drop Leg w/ Spring Return - Traditional - 26" Lift # BD183903 (front facing plunger pin)
Bulldog 2-Speed Jack - Drop Leg w/ Non-Spring Return - Traditional - 26" Lift # BD183901 (front facing plunger pin)
Bulldog 2-Speed Jack - Drop Leg w/ Spring Return - Traditional - 26" Lift # BD183902 (side facing plunger pin)

The Replacement Gear Assembly for Bulldog 2-Speed 12,000-lb Jack, part # BD500295 is also available for these jacks.

expert reply by: Carla M

0

Answer 1

We do have the Bulldog 2-Speed Jack #BD183401 without a spring return. This is a 10,000lb lift capacity 2-speed jack similar to the etrailer #TJD2SP-12000SP-F jack you found. The Bulldog requires a separate Handle #BD701466 as one is not included. We…

view full answer...

Answer 2

For your Bulldog 2-Speed 10K Jack #BD183816 the powered drive kit to use is part #BD1824180100; I confirmed this with the tech team at Bulldog. The power drive kit will install with the motor on the inboard side, closer to the trailer. The written…

view full answer...

Answer 3

The torque for the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles - 12" - 5 Spoke Utility #8-174-5UC3 is not specified by the manufacturer. For 9/16 inch studs, the typical lug nut torque will be 120-140 ft lbs based on most…

view full answer...

Answer 4

Since we don't have a powered drive kit for the Ram jack #TJD-12000SP-F2 your best option would be to use the powered drive kit part #BD1824180100 with the Bulldog 2 speed jack part #BD183416 and you'd be set.

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Availability of Bulldog 12,000 lb 2-Speed Trailer Jack

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching