What is the Inner Diameter of the Pro Series Detachable Footplate # PS1400700340?

Question

Question:

on the 2 inch diameter. is that 2 inch inside dia. or outside dia.?

asked by: Robert G

0

Expert Reply:

The 2-inch diameter measurement of the Pro Series Detachable Footplate w/ Pin for 2" Diameter Jacks # PS1400700340 is the inner diameter. It is designed to fit jacks that have an inner tube diameter of 2 inches like the Pro Series Round, A-Frame Jack # PSEA20000103.

expert reply by: Bob C

0

Answer 1

Hey Kevin, for a foot plate that fits your Pro Series Jack #PSRV20000103 the part #PS1400700340 is the recommended plate.

view full answer...

Answer 2

Absolutely! The Replacement Footplate #JF-100-ZBK you were looking at fits all jacks with a 2-1/4" outer tube, and 2" outer tube. Since that is what your Ultimate Trailer Jack #322-RDJ-2K has, this will be an exact replacement. Both the…

view full answer...

Answer 3

For the Ram jack part #TJA-2000-Z we have a replacement foot with the part #JF-100-ZBK or a wheel caster like part #JC-102 but the Ultra Fab foot you mentioned would not fit.

view full answer...

Answer 4

I went out to the warehouse to measure the Pro Series Round, A-Frame Jack, #PS1401000303. The outer tube is 2-1/4 inches in diameter. The inner tubing is about 1.97 inches in diameter. This jack does not come with a wheel or footplate. For a wheel,…

view full answer...

Answer 5

Yes, the Drop Leg for etrailer and Ram Jacks part #JF-1005H-Z will fit the Ram Round A-Frame Trailer Jack part #TJA-2000-Z and provide an additional 8" of lift. It also has a round footpad which will make the jack much sturdier as there is a…

view full answer...

Answer 6

I do have an option for you but we can't confirm Bulldog jack caster wheels will work with a Ram Series 2000 Trailer Jack. That said, we do offer caster wheels for this jack, the Ram Removable, 6" Poly Caster Assembly for 2" Jack Tube…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

What is the Inner Diameter of the Pro Series Detachable Footplate # PS1400700340?

Featured Help Information

Miscellaneous Media

Continue Researching