What is Bolt Pattern of Trailer Brake Assemblies 23-180-181

Question

Question:

What is the measurement center to center on the holes in the mounting plate?

asked by: Gary W

1

Helpful Expert Reply:

I attached a picture that shows the bolt pattern of the trailer brake assembly part # 23-180-181 that you referenced.

expert reply by: Jameson C

1

trailer brake assembly 5 bolt pattern
(click to enlarge)

Answer 1

Hi Jim! The Dexter Electric Trailer Brakes - 12" - Left/Right Hand Assemblies - 7,000 lbs #23-180-181 does indeed come as a pair, so one left and one right brake. Each quantity of one with be enough to replace the brake on one axle. So if you…

view full answer...

Answer 2

I just confirmed with Dexter that the Dexter Electric Trailer Brake Kit - 12" - Left and Right Hand Assemblies - 7,000 lbs item #23-180-181 you were looking at are the correct replacements for the AL-KO brake assembly part #s 363233.1 and…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 7

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 8

Hey there Trace! There are parts of the steel brackets that come into contact with the aluminum bed on your new 2026 F350 Super Duty (congrats on the new truck by the way - those are super nice!). B&W says to use strips of polypropylene tape…

view full answer...

Answer 9

With a 2022 F350 short bed, hitting the top of the bed rails should not be an issue with most campers. Turning clearance however, will certainly be a factor. That is one advantage of the Andersen Ultimate hitch #AM3200, as it provides a 9"…

view full answer...

Answer 10

Based on the pictures you provided you most likely have the B&W Turnoverball Underbed Gooseneck Trailer Hitch w/ Custom Installation Kit - 30,000lbs #BWGNRK1111. You definitely lucked out having a B&W gooseneck hitch because you'll be…

view full answer...

Answer 11

Hey Judah, For below bed you would need to go with the B&W Turnoverball Underbed Gooseneck Trailer Hitch #BWGNRK1108 and then use either the fixed base Companion #BWRVK3500 or slider base Companion #BWRVK3400-5W depending on whether you have a…

view full answer...

What is Bolt Pattern of Trailer Brake Assemblies 23-180-181

Product Page this Question was Asked From

Continue Researching