Recommended Trailer Brake Controller For a 2022 Ford F-150 With Factory Tow Package

Question

Question:

What brake controller do you recommend for my 2022 Ford F-150? It has the factory tow package so I have all the wiring for my campers 7-way.

asked by: CJ

0

Expert Reply:

I recommend the Tekonsha Prodigy P3 Trailer Brake Controller for your 2022 Ford F-150. This brake controller is proportional so once you have it adjusted to your trailer it will automatically adjust braking output for light and severe braking situations. This will help keep you from worrying about reaching down to adjust the trailer brake pressure is those situations. The LCD screen is customizable and the built in diagnostics help you to troubleshoot any issues that might occur with the trailer braking system.

The Tekonsha Plug-In Wiring Adapter # 22292 will make the installation virtually plug and play as you will only need to attach the mounting bracket for the controller to your dash after you plug into the factory connection under your dash.

expert reply by: Bud M

0

Michael

2/7/2025

Your article says to use adaptor 22292 on a 2022 Ford F150. However, when I select that item; its says it does not fit my truck which is a 2022 F150.

Robin H.

2/8/2025

@Michael do you have a factory tow port on your 2022 F-150 for a brake controller? If not, it is likely at the time this answer was written we weren't aware of a change in the F-150. Ford still uses this connector on current models like the F-250 and F-350. If you don't see the plug that matches this wiring harness connector under the dash it is safe to assume you have to splice for installation.

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 12

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...