Replacement Remote for Jensen RV Stereo JWM70A

Question

Question:

I am looking for a replacement remote for Jensen JWM70A stereo

asked by: John

0

Expert Reply:

The correct replacement remote for your Jensen RV Stereo JWM70A comes in the Replacement Service Pack # JEN55VR. The remote isn't available outside of the service pack but in my experience it's never a bad thing to have some extra wiring laying around for a rainy day.

expert reply by: Jon G

0

Answer 1

The only way you can get the replacement remote control for the Jensen RV Stereo - Single DIN - AUX/USB, Bluetooth, jControl - 12V, part #JWM70A, is to get the Replacement Service Pack for Jensen RV Stereo, part #JEN55VR. I have included a product…

view full answer...

Answer 2

For your Furrion FMCM15-BL Microwave, we have the Replacement Square Cooking Rack #324-000152, and the Replacement Round Cooking Rack #324-000151. The #324-000151 measures 2-9/16" tall, and has a diameter of 11-15/16". We do not offer a…

view full answer...

Answer 3

To replace the remote for your Jensen #JWM70A you'll need the replacement service pack #JEN55VR. This stereo uses an infrared sensor to register what the remote is doing, so all you have to do is put in the batteries and point the remote at the…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Replacement Remote for Jensen RV Stereo JWM70A

Featured Help Information

Miscellaneous Media

Continue Researching