Replacement Bearing Kit for Trailer Hub with L44643 Bearing

Question

Question:

Hi,I have a utility trailer and I need to replace the bearings.I can’t make out the number on the outer bearing the inner bearing number is L44643.The part number on the hub is OL 6541.Any help would be greatly appreciated.Thanks

asked by: Mario

1

Helpful Expert Reply:

The L44643 bearings are almost always used in pairs so it's safe to say that you'll need the Bearing Kit with Grease Cap for 1" BT8 Spindle part # DL21792.

expert reply by: Conner L

1

Answer 1

I was unable to find any specific information about your trailer but I can help you determine which bearings you will need. If you have the old bearings they should be stamped on the back with the part number. If you do not have them or the number…

view full answer...

Answer 2

I would love to help but we don't have any bearing or seal information for specific trailers. This is just not information that the manufactures release to the public. If you want to find the correct replacement bearings and seals you will have…

view full answer...

Answer 3

There are two different options of idler hubs that we have available for a 2,000 pound axle. You will have to first let us know what your bolt pattern is which I will link a link below to help you find out what your pattern is. Next we will need to…

view full answer...

Answer 4

Before proceeding, I'd take a moment to confirm the spindle diameter, because there are two different bearing sets that are very close in dimension, so you'll want to be absolutely sure of the measurement you get. We recommend using a digital…

view full answer...

Answer 5

When it comes to replacing the hub and drums on your 40 year old boat trailer I recommend TheCE Smith Trailer Idler Hub Assembly w/ Case for 2.5K Axles - 5 on 4-1/2 - Galvanized - Pre-Greased #CE13215. This trailer hub and drum has a sturdy iron…

view full answer...

Answer 6

After you've packed the bearings and assembled everything, carefully slide the hub assembly onto the spindle and install the outer bearing. Install the spindle and tang washer and run the spindle nut down finger tight, then rotate the hub back…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Replacement Bearing Kit for Trailer Hub with L44643 Bearing

Product Page this Question was Asked From

Continue Researching