Center To Center Mounting Hole Measurement For Bauer Motorhome Door Lock Strike Plate

Question

Question:

Looks like it may fit, but need measurement on strike plate.

asked by: George C

1

Helpful Expert Reply:

I spoke with the manufacturer and the Bauer Products Motorhome Door Lock - Black # BA64FR strike plate mounting holes has a 5-1/2" measurement from center to center.

expert reply by: Kevin C

1

BA64FR Strike Plate Mounting Holes
(click to enlarge)

Answer 1

Hello Doug. The Bauer Products Motorhome Door Lock #BA64FR is definitely going to be your best bet for replacing the latch on your horse trailer door. This latch is made to fit a 5-1/4" wide x 4-1/2" tall cutout. With your hole being only…

view full answer...

Answer 2

The Bauer Products Motorhome Door Lock #BA64FR and it's sister option #BA65FR are the only options we carry that are close enough to fit your 5" wide by 4-3/4" tall (with minor trimming to get your 5" width to 5-1/4"). The…

view full answer...

Answer 3

We have a very similar entry door lock with the Bauer Products Camper Door Lock #BA65FR. The configuration appears to be very similar to the lock on your 2004 Featherlight horse trailer. The Bauer lock is made to fit a cutout 5-1/4" wide x…

view full answer...

Answer 4

Hey Lyn, it's going to come down to the cut out size of the door where the current latch installs. If it's right at 3 inch by 4 inch you'd want the #295-000019 or if it's 5-1/4" wide x 4-1/2" tall you'd want the part…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Center To Center Mounting Hole Measurement For Bauer Motorhome Door Lock Strike Plate

Product Page this Question was Asked From

Continue Researching