How to Remove RV Safe RS34FR Carbon Monoxide/LP Gas Detector

Question

Question:

How do you remove the detector

asked by: Will D

0

Expert Reply:

The RV Safe # RS34FR Carbon Monoxide/LP gas detector is held to the wall using two screws. Remove the screws and you'll be able to pull the detector from the wall exposing the wiring. The red wire from the detector is connected to a 12-v power source, the black wire is connected to a ground.

I've linked to the installation instructions for you, as well as to a demonstration video.

expert reply by: Mike L

0

Wiring Diagram for RS34FR RV Safe Carbon Monoxide/LP Gas Detector
(click to enlarge)

Answer 1

You could use the 2-wire Propane Gas and Carbon Monoxide Detector part #RS34FR in place of the Atwood 36681 that you referenced. This would fit in the cut out you have now and has a flange that is large enough that would cover the hole.

view full answer...

Answer 2

I recommend the #RS34FR to replace your current LP gas detector. This is a simple 2 wire design making for easy installation.

view full answer...

Answer 3

Hey Wayne, to replace the Atwood propane gas detector you have now you could use the part #AT36681 which also is a carbon monoxide detector.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

You can use the RV Propane Gas Detector #RS64FR (white) or #RS44FR (black) to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...

Answer 7

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

How to Remove RV Safe RS34FR Carbon Monoxide/LP Gas Detector

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching