Surco Safari Roof Rack Adapter Needed For A Hummer H3

Question

Question:

I have sps5060 -1101 for 2008 hummer Will ch100 mount to my factory rails then mount to rack

asked by: Dennis S

0

Expert Reply:

Yes, the Adapter for Surco Safari Roof Racks # SPCH100 will mount to your factory rails allowing you to mount your Surco Safari Rack 5.0 Rooftop Cargo Basket for Factory Rails # SPS5060-1101 to your 2008 Hummer H3.

expert reply by: Kevin C

0

Answer 1

Hi Herman, The roof dimensions of your 2005 Ford Excursion are 120" long x 55-56" wide, so you should have plenty of room for the Surco Safari 5.0 rack that is 84" long x 50" wide to fit on your roof. This cargo basket does have…

view full answer...

Answer 2

Hey Daniel, The Adapter for Surco Safari Roof Racks #SPCH100 would require rails in order to install. The base of the adapters has two holes which will each get a bolt and square nut that would sit inside of a track in the rails. You can add rails to…

view full answer...

Answer 3

Yes, the tracks themselves recreate the factory C-shaped rack tracks. Thule Tracks #THTP42 and Yakima Tracks #Y01126 have the same C-channel design, but differ in length and how they mount to the vehicle. To use your SkyLine Towers #Y53TR with these…

view full answer...

Answer 4

The different Safari Rack packages are due to hardware adapter kits for various vehicles. In the case of the Sprinter 2500 you will need: Surco #SPS5084 Safari Rack Surco #TC97FR Crossbars 60" Surco #SPCH100 Adapters (order 2) Surco #R6200 Roof…

view full answer...

Answer 5

It's always best to use adapters made for the Surco Safari Rack #S5072 so it's secure. That being said the U bolts you're looking at #CTC-18PARTS isn't the best option. You need these rails #SPR3600 for your factory roof rack.

view full answer...

Answer 6

If you're installing the Surco Safari Rack 5.0 Rooftop Cargo Basket #S5050 and Adapter Ki #SPCH100 on your 2018 Ford F-150 then you also need the 36" Roof Rails #SPR3600. These install onto the roof of your F-150 and then the adapter rails…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Surco Safari Roof Rack Adapter Needed For A Hummer H3

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching