Replacement Bearings and Brake Assemblies for Lippert 4,000 lb Axle

Question

Question:

Hi, I recently purchased a pop up camper with a Lippert 136216 axle 4000 lb. I would like to service and replace the bearings, drums and brakes. Are you able to obtain the respective part numbers for recommendations from the axle number?

asked by: Adam S

0

Expert Reply:

For the Lippert 4,000 lb axle trailer hubs the bearings are # 25580 for the inner bearing and # LM67048 for the outer. So for a kit that has both you'd want the # BK3-310.

Then for self adjusting brake assemblies you could use the part # AKEBRK-35R-SA for the right hand side and # AKEBRK-35L-SA for the left.

expert reply by: Jameson C

0

Answer 1

Hey Amie, for a Dexter axle with the weight rating you listed the correct grease seal would be the part #34823.

view full answer...

Answer 2

Hey Roger, for the Lippert 4,000 lb trailer axle we have found that the bearings used are the same as the 3,500 lb axles so you would just need the part #BK2-100 for a kit that includes the bearings and the seal.

view full answer...

Answer 3

It is a very good idea to keep spare bearings and seals (and wheel bearing grease too) on hand for the unexpected roadside stop. We have individual bearing and seal parts like #L68149, #L44649 and #58846 as well as kits like #BK2-100 that combine…

view full answer...

Answer 4

Hey Don, The Loadstar ST205/75D14 Bias Trailer Tire with 14" Galvanized Wheel - 5 on 4-1/2 - Load Range C #AM3S450 would be the correct fit but I would double check the load range on your current tires. If you find you have a load range D…

view full answer...

Answer 5

Hey Kyler, thanks for reaching out! **UPDATE IN COMMENT SECTION - JUMPER LOCATION IS DETERMINING FACTOR** The Progressive Dynamics Replacement Section #PD4655V is compatible with lithium batteries. There is a button on the board (see photo) that…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Replacement Bearings and Brake Assemblies for Lippert 4,000 lb Axle

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching