What Does 5 on 4-1/2 inch Bolt Pattern Mean in Relation to Trailer Wheel

Question

Question:

What does 5 on 4 and 1/2 mean

asked by: Jeff Y

0

Expert Reply:

The phrase 5 on 4-1/2 inch is the bolt pattern of the wheel. This means that there are a total of 5 lugs that hold the wheel to the hub and the distance across the hub from the center of one lug straight across is 4-1/2 inch. This is the bolt pattern that the part # AM3H390 you referenced has and is by far the most popular 5 lug bolt pattern.

expert reply by: Jameson C

0

Answer 1

etrailer is from the US. We are right in the middle near St Louis MO in a town called Wentzville. But we sell products that are made all over. Some from US and some from other countries as well.

view full answer...

Answer 2

In order to replace the 20.5x8.0-10 wheels/tires I recommend using 205/65-10, the Kenda 205/65-10 Bias Trailer Tire with 10" White Wheel part #AM3H390 in particular which has an 81 mph speed rating. It will fit the same hubs you have now so you…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 7

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6 inch whereas the 225/75-15 fits widths that are 5 inch to 6-1/2 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

What Does 5 on 4-1/2 inch Bolt Pattern Mean in Relation to Trailer Wheel

Product Page this Question was Asked From

Continue Researching