Correct Replacement Inner Slide for UFP A-70 Surge Brake Actuator

Question

Question:

My pontoon trailer has a stamp on the front of trailer for a A-70 This is a 2005 Metal Craft Trailer what hitch is best for replacing the old style surge brake Drum style .

asked by: Jennifer R

0

Expert Reply:

The Replacement Inner Member for Dexter DX7.5L Brake Actuator part # DX97FR is compatible with a UFP A-70 Surge Brake Actuator.

expert reply by: Conner L

0

Answer 1

Hi Charles, While we don't currently offer the inner member that you're needing for the UFP A-70 we do offer a compatible replacement with the Dexter DX7.5L A-60 Brake Actuator #DX33FR. This is the entire actuator assembly along with the…

view full answer...

Answer 2

The Mini Thin Line Sealed LED Marker/Clearance Light, #MCL-91AK, will attach to the trailer using 2 screws which are included. I have included a picture showing the mounting holes for you.

view full answer...

Answer 3

If a trailer clearance light like part #MCL44AB1 is used, the one wire is the power wire for the light and the light will be grounded through the mounting hardware. If you want to use the ground wire that you have on your trailer you can install part…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Correct Replacement Inner Slide for UFP A-70 Surge Brake Actuator

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching