Installing and Removing Sumo Spring Supports for 2020 Subaru Outback Wagon

Question

Question:

Once installed, can these be easily removed and reinstalled when I have a load on the trailer hitch? I use a motorcycle carrier thank you and the back droops a bit but I like the unloaded ride. Thanks.

asked by: Bruce G

0

Expert Reply:

Yes, the Coil SumoSprings Custom Helper Springs item # CSS-1125R can be removed by following the same steps as you did when you installed them. All you have to do is reverse steps 5-7 once you get the car jacked up and the tension out of the springs.

expert reply by: Jerred H

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 6

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 7

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 8

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 9

Hi Mark; I'm sorry to say the mirrors for the F-150 will not fit your 2024 Ford Expedition. Since no custom towing mirrors are available, the best option is the K-Source Universal Towing Mirrors #KS3891-2. These have ratcheting straps to keep…

view full answer...

Answer 10

Hey Ray, while there certainly is a lot of appeal to the Andersen WD systems like the part #AN88VR what we have found is that if the tongue weight is more than a few hundred lbs they just don't work as well as the traditional systems that use…

view full answer...

Answer 11

Hi Sabrina! Though I definitely have an option for you, the #CIP56VV is a replacement passenger side towing mirror for a 2021 to 2023 Ford F-150 and will not be what you are looking for. Unfortunately, there are no custom fit options available for…

view full answer...

Installing and Removing Sumo Spring Supports for 2020 Subaru Outback Wagon

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching