How Do I Solve Water Leakage on My BAK Tonneau Cover?

Question

Question:

Do you need to cut excess hose from the water relief hoses or just shove them threw . Im trying to figuer why im getting this water on my bed walls

asked by: Scott M

0

Expert Reply:

I went ahead and brought your issue to my contact at BAK about your BAK tonneau cover, and he confirmed that you can either trim the hose or shove it through the hole. He also recommended using silicone around the nipple to deter leakage.

expert reply by: Bob C

0

Answer 1

Hi Mark; B&W does not have a 3" version of the Tow & Stow Pintle Hook at this time. What you can do is use the #BW77BR for a 2-1/2" hitch along with the BTBRV Magnetic Hitch Receiver Reducer Sleeve #BTBRV74FR. The reducer sleeve…

view full answer...

Answer 2

It sounds like you have some older 2" accessories that you need to work with your new 2-1/2" receiver. We have you covered. One option you have is to simply use a reducer sleeve like the B&W Hitch Receiver Reducer Sleeve, part…

view full answer...

Answer 3

This is a great question that there isn't exactly a great answer for. Hitch extenders not only put the weight further away from the hitch which would increase the leverage on the hitch, but they also add movement to the assembly which will…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 10

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 11

Hey Brian! It looks like you decided to go with the MORryde GooseTech #MR27MV, which is a great option. However, the GVWR of your 2023 Keystone Montana 3231CK is 16,680 lbs and this is designed for 18k+. Also, did you verify that your pin box bolt…

view full answer...

Answer 12

Hello David, Thanks so much for reaching out! For your 2026 Ford F-350 diesel dually, you will want the EcoHitch Hidden Front Mount Trailer Hitch Receiver - Custom Fit - 2" #EH54QR. This is the only front mount option we offer that is confirmed…

view full answer...

How Do I Solve Water Leakage on My BAK Tonneau Cover?

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching