Can the Swagman Current be Used with a Class 1 Hitch Receiver?

Question

Question:

Good afternoon I bought the swagman current because of the ebike status and ask vendor if it was good to go on a class 1 hitch and he said yes but after reviewing a few articles Im sure anymore.My ebikes weight 36lbs each without the batteries and the swagman current rack weighs 49lbs for a total of 121lbs can a class 1 hitch take this kind od weight.

asked by: Edward

0

Expert Reply:

When considering to put the Swagman Current # S64678 on a class 1 1-1/4 inch hitch, it truly depends on the maximum tongue weight of your hitch. Usually, class 1 hitches have a maximum tongue weight capacity of around 200 pounds. However, I strongly recommend that you consult the instructional manual of your hitch or provide me with the make/model of hitch that you have to confirm the tongue weight capacity. Also, I confirmed with my contact at Swagman that even if the bike/rack weighed under the maximum tongue weight capacity, the Swagman Current would not be covered under warranty if it gets damaged (since the Current is only listed for 1-1/4" hitches that are class 2).

If you want a bike rack that can hold your electric bike and is rated for class 1 hitches, I recommend the Saris SuperClamp EX Bike Rack for 2 Bikes - 1-1/4" and 2" Hitches # SA4025F. The Classic 2 has a per-bike weight capacity of 60 pounds and has a carrier weight of only 35 pounds. As far as clearance of your rear bumper, you will have no issues as long as the measurement from the center of your hitch's pinhole to the outside of your bumper is less than 7-1/4 inches long.

If you need a recommendation of a rack with a longer shank or if you need a hitch receiver recommendation, I would be happy to give you those recommendations if you provide the year/make/model of your vehicle.

expert reply by: Bob C

0

Answer 1

The great thing about the Swagman XTC2 part #S64670 is that it fits both hitch sizes without requiring additional adapters. Basically the shank of the rack fits a 1-1/4 inch hitch but it also comes with a sleeve type adapter that allows it to fit…

view full answer...

Answer 2

Both Class I and Class II trailer hitches have the same 1-1/4 inch receiever opening, however a Class II hitch will have higher towing and tongue weight capacities. The primary issue with using a Class II accessory in a Class I hitch is that many…

view full answer...

Answer 3

The reason that you can't use a Class II adapter in a Class I hitch receiver is that most Class I hitch receivers have a lip or stopper that keeps you from using the longer shank of the Class II adapter in the lower capacity Class I hitch. You…

view full answer...

Answer 4

Hey Robin, The Swagman XTC2 Bike Rack #S64670 installs with a threaded hitch pin which is fine, but can be a bit of a pain in the butt if you're planning on taking it on and off your 4Runner frequently. A LOT of bike racks use this style of pin…

view full answer...

Answer 5

For Curt trailer hitch #C11416 for the 2016 Honda HR-V if you have an all wheel drive model then there is no cover, lines, or fascia have to be removed, trimmed, or otherwise manipulated to install the trailer hitch. But on front wheel drive models…

view full answer...

Answer 6

The Swagman XTC-2 2-Bike Platform Rack part #S64670 is only rated for use on Class II and above per Swagman. The next most similar cost effective option we have that is class I compatible is the Curt 2 Bike Platform Rack part #C18085.

view full answer...

Answer 7

I reached out to Swagman and my contact confirmed that the Swagman XTC-2 2 Bike Platform Rack #S64670 will work with a Class I trailer hitch receiver on your 2020 Kia Soul. She mentioned the reason they only show Class II on their website is to make…

view full answer...

Answer 8

The Curt Class I hitch, part #C11416 has a shipping weight of 19 pounds. So, the hitch weighs around 16 pounds. If you're planning on using the hitch as a mounting point for a bike rack or a cargo carrier (and you probably are), remember that…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Can the Swagman Current be Used with a Class 1 Hitch Receiver?

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching