Is Mounting Hardware Available for Malone Bunk Kit # MPG561

Question

Question:

I have the low max trailer. I am going to make a set of bunks for it . Can I order all of the hardware from the MPG561 kit minus the straps and bunks ? If so, is there a part # or sku ? Thank you

asked by: David H

0

Expert Reply:

Malone doesn't offer just the hardware of the # MPG561 that you referenced. You can only order it with the bunks which would certainly be easier than making them yourself!

expert reply by: Jameson C

0

Answer 1

Hey Stefano, yes the LowBed kit part #MAL33TR is all that you need to convert your Malone Microsport #MPG460XT to a LowBed style trailer. The Yakima DeepSpace part #Y65RR is also compatible with the 2nd Tier Kit part #MPG474 too. How come you are…

view full answer...

Answer 2

Hello Jeremy. The Malone Eco Light Trailer like part #MAL53FR comes with a 4.80/4.00-8" load range B trailer tire. If you are looking for an upgrade, I recommend the Kenda 4.80/4.00-8 Bias Trailer Tire with 8" Galvanized Wheel #AM30070.…

view full answer...

Answer 3

I spoke with Malone about which Bearing Buddies you should use on the Malone EcoLight Sport Trailer with V-Style Carriers for 2 Kayaks #MAL43FR and they said that they do not recommend using Bearing Buddies on any of their trailer, however if…

view full answer...

Answer 4

Chenchar, I recommend you upgrade your 8" tires on your Malone EcoLight Trailer #MAL43FR to a 10" wheel using the Kenda 205/65-10 Bias Trailer Tire with 10" Galvanized Wheel #AM3H490. These wheels are going to have the same bolt…

view full answer...

Answer 5

Hey Coy, You can replace the 8" wheels on your Malone EcoLight Sport Trailer #MAL73FR with ones like the Kenda 4.80-12 Bias Trailer Tire #AM30590. Before doing so you'll want to measure the distance between the tire and fender as well as the…

view full answer...

Answer 6

The Malone EcoLight Sport Trailers like item #MAL43FR have 8" tires with a 5 on 4-1/2 lug pattern. The Kenda 205/65-10 Bias Trailer Tire with 10" Galvanized Wheel item #AM3H490 would work as a replacement but you will most likely have to…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Is Mounting Hardware Available for Malone Bunk Kit # MPG561

Product Page this Question was Asked From

Continue Researching