Correct Vehicle and Trailer Side Hopkins Endurance 4-Way Flat Trailer Connector

Question

Question:

Is this a plug and play from my RV to my trailer

asked by: Mike

0

Expert Reply:

The Hopkins Endurance 4-Way Flat Trailer Connector part # HM48110 is a trailer side connector which is designed to be installed on the towable. If you're instead looking for the vehicle side which is designed to be installed on the tow vehicle then you will need the Hopkins Endurance 4-Way Flat Trailer Connector part # HM48030. These harnesses both require splicing whether you are just replacing a trailer connector or wiring one for the first time.

expert reply by: Conner L

0

Answer 1

The Hitch I recommend for your 2022 Chevy Colorado is the Curt Trailer Hitch Receiver #C13176. This hitch is Made in the USA, will fit all models of the 2022 Colorado and has a bolt-on, no drill installation. This hitch will also provide you with a…

view full answer...

Answer 2

The best trailer wiring harness for a 2015 Chevrolet Colorado is the Hopkins Multi-Tow 7-Way Blade and 4-Way Flat Trailer Connector part #HM11141144 because it comes with both 4 and 7-way trailer connection points and it installs inside the factory…

view full answer...

Answer 3

Yes, you can trim the BedRug or BedTred to fit around your 5th wheel rails. If you end up needing more hook and loop fasteners, you can find that here Supplemental Installation Kit #BRZSPRAYON. If your 2018 Chevy Colorado has the 5 foot bed, go with…

view full answer...

Answer 4

For your 2020 Hyundai Palisade Limited edition you will need a wiring kit to transfer the light signals to your trailer, the pre-wiring provides a plug for the trailer wiring to hook up. I recommend Curt T-Connector Vehicle Wiring Harness #CU94FR. It…

view full answer...

Answer 5

It sounds like you have a common ground problem. When the headlights are on, the highest amperage draw is placed on the wiring system and if you have a bad or loose ground, you will have problems with lights. You will want to inspect to make sure all…

view full answer...

Answer 6

We do have the Hopkins Plug-In Simple Vehicle Wiring Harness #HM11141164 which will allow you to plug into the tail lights on your 2019 Chevrolet Colorado. Do understand this will require you to run a dedicated power wire to the battery under the…

view full answer...

Answer 7

The holes on the 4-Way connector of #HM48030 are space 1-5/8 inches apart on center. None of the brackets are a perfect match.

view full answer...

Answer 8

4-pole trailer wiring is usually described as vehicle-side and trailer-side since the male/female description that works well for other items can be confusing when applied to connectors. The part you referenced, Optronics #A35W42B, is a 42-inch…

view full answer...

Answer 9

You have two alternatives for replacing your factory 4-pole trailer connector. First, you can simply abandon the old connector by taping it up out of the way and use what's called a T-Connector like part #118329. A T-Connector would plug inline…

view full answer...

Answer 10

The 58" long x 20" wide x 5/16" thick Westin Custom Fit Tailgate Mat #50-6505 requires a 9/64 diameter drill bit for the mounting hardware (see cutout of instructions). Please note that this tailgate mat is designed for various years…

view full answer...

Answer 11

It sounds like you are looking for trailer wiring that fits your 2018 Chevy Colorado that does not have a 7-way currently. For that the easiest to install kit is the Hopkins part #HM11141164 which installs easily by plugging inline with the taillight…

view full answer...

Answer 12

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Correct Vehicle and Trailer Side Hopkins Endurance 4-Way Flat Trailer Connector

Continue Researching