Wedge Kit For A Lippert Turning Point Pin Box And B&W Patriot 5th Wheel Hitch

Question

Question:

Which Wedge do you recommend for a Bandw 3300. We are hooking up to a Turning point pivot hitch. the fifth wheel is a Grand Design Reflection 240 Rl

asked by: Robert A

0

Expert Reply:

The correct wedge for your B&W Patriot 5th Wheel Hitch # BWRVK3200 and Lippert Turning Point pin box is the Wedge Block for Lippert Turning Point Pin Box Item # LC79UD.

expert reply by: Kevin C

0

Answer 1

The Lippert Turning Point has a specific bolt pattern that only has one replacement so far, the Gen-Y Hitch Shock Absorbing 5th Wheel to Gooseneck Pin Box #GY48GR. This is a gooseneck adapter though so you'd have to switch out the hitch for a…

view full answer...

Answer 2

That's great information - I appreciate it! The Gen-Y Executive needs at least 1,600 lbs tongue weight to be able to use the lightest option. When using a 5th wheel or gooseneck setup you want your tongue weight to be 20% of the weight of the…

view full answer...

Answer 3

If you are having trouble fitting the wedge that came with your Lippert Turning Point pin box to your 18K B&W Patriot #BWRVK3255 then you can use the Custom Wedge #SWW-06 instead. This is actually designed for use with the Reese Sidewinder pin…

view full answer...

Answer 4

A wedge is needed, yes, and the Lippert Turning Point pin box does come with a universal wedge, but it is not a very good fit with the B&W Companion #BWRVK3710. So I highly recommend instead using the 5th Airborne Custom Wedge for B&W Fifth…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Wedge Kit For A Lippert Turning Point Pin Box And B&W Patriot 5th Wheel Hitch

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching