Replacement for TDE Trailer Hub Part 46210 with Transcom 168255TB Seal

Question

Question:

my hub seal says its a Transcom #168255TB why the difference

asked by: Richard

0

Expert Reply:

The Trailer Idler Hub Assembly for 3,500-lb E-Z Lube Axles part # AKIHUB-545-35-G-EZ-K is compatible with the Double Lip Seal for 3,700-lb Marine Hubs part # 168255TB which is the same as a Transcom 168255TB. This will be a great replacement option for the TDE Trailer Hub Part 46210.

expert reply by: Conner L

0

Answer 1

Hey Eddie, thanks for the pictures. From seeing that I can tell you have a 3,500 lb axle and the correct replacement hub would be the part #AKIHUB-545-35-G-EZ-K that you referenced which comes with new bearings and seal.

view full answer...

Answer 2

There typically aren't any part numbers stamped onto the trailer spindle that can be used for identification. There are however numbers stamped onto the hub most times which can be used for identification. The TDE46210 tells me you have a 3,500…

view full answer...

Answer 3

Harbor Freight trailers are unique. They don't have any industry standard parts on them, so replacement parts are very difficult to find. We don't have any grease caps that will fit your 2-inch hub. It may be possible to replace your hubs…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 11

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Replacement for TDE Trailer Hub Part 46210 with Transcom 168255TB Seal

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching